Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem D2.51P
To determine
The expression for the gain as a function of the given potentiometer, the range of gains at given condition, the value of the resistance.
To show: The addition of a fixed resistor for the given gains.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The following Operational Amplifier circuit is given. Analyze the circuit
carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps.
Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
The following Operational Amplifier circuit is given. Analyze the circuit
carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps.
Calculate the first stage output voltage Vx and then the output voltage at the output of
the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the
power absorbed by the resistor R7. The resistors: R2 = R4 =100KW. R1 = R3 = 10W,
R5 = 10W, R6 = 90 KW. and R5 = 10W. The load resistor R7 = 10KW. The current
source; I1 = 100μA and V2 = 1V.
Problem 3:
Derive the gain of the operational amplifier circuit below using the op-amp voltage rule and
op-amp current rule. If the resistor R2 =1 k2, the input voltage vin =
voltage vout = 5 V DC, what should the resistance of R1 be?
0.1 V DC and the output
%3D
wwww
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q2) Why is there a difference between the theoretical and practical values of voltage gain in an inverting and non-inverting Op amplifier?arrow_forwardThe ideal op-amps depicted can swing rail-to-rail at output, and Vcc= 13 V. Initially, the output voltage Vo = +13 V and the input voltage is vS = -13 V. The feedback resistors are R1 = 6.4 k0, R2 = 8.5 kQ, and R3 = 1.6 KQ. If the input voltage is gradually increased, at what value of vS (to 1% accuracy) does the output voltage (Vo) change to Vo=-Vcc? VVV vS = + R10 Vcc -Vcc R20 04 O Voarrow_forwardIf the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .. . mVarrow_forward
- By using only two op-amps, design a circuit that can perform the following operation: Vo == Also, evaluate the given circuit equation. Show all the assumptions, calculation and the circuit illustration. Marking Scheme: Circuit Design Assumptions Calculationarrow_forwardAn op-amp intended for operation with a closed-loop gain of -100 V/V uses resistors of 10 k2 and 1 MQ with a bias-current-compensation resistor R3. Assuming an ideal voltage source at the input, what should the value of R3 be? With input grounded, for one particular op-amp, the output offset voltage is found to be +0.30 V. Estimate the input offset current assuming zero input offset voltage. In this case, if we know the input offset current is one-tenth the bias current what value of R3 will result in zero output offset voltage?arrow_forwardSubject : Electronics Engineering Draw circuits for both inverting and non-inverting amplifier using op-amp. Derive the expression for the gain of an inverting amplifierarrow_forward
- For the ideal op-amp shown, what should be the value of resistor Rf to obtain a gain of 12?Answer should be in kiloOhm.arrow_forwardThe voltage transfer characteristic for an operational amplifier shown (a) What are the values of gain and offset voltage for this op amp? (b) Plot voltage gain A versus vid for the amplifier voltage transfer characteristic.arrow_forwardQ1 (a) (b) Considering an op-amp, define what is meant by input offset voltage (Vos) and explain what causes it. Figure Qla shows an integrating amplifier with zero input. Derive an expression for the output voltage, Vo, and explain the effect that Vos will have on its operation. R W Vos C Figure Qla A •V₂arrow_forward
- Q1) Compare the practical results and the theoretical results for the Inverting Op-Amp and also compare it for the non-inverting Op-Amp.arrow_forwardDiscussion: 1- What kind of restrictions Non- inverting op-amp face compared to inverting op-amp? 2- State 5 different types of op amp. Demonstrate them briefly then draw the circuit diagram for each kind. 3- For an inverting op amp, if the voltage input peak equal to 10.2 V, R=10KQ and RF 2002, find Vo and the voltage gain. Assume the input signal has a sinusoidal behavior. 4- Consider an OP amp connected to the inverting configuration to realize a closed-loop gain of -50 V/V utilizing resistors o f 1 k2 and 50 kQ. A load resistance RL is connected from the output to ground, and a low-frequency sine wave signal of peak amplitude Vp is applied to the input. Let the OP amp be ideal except that its output voltage saturates at +/- 10V and its output current is limited to the range +/-15 mA. For RL = 1 k2, what is the maximum possible value of Vp while an undistorted output sinusoid is obtained?arrow_forwardPower Amplifier Based on your own study, explain class C and class Damplifiers. What is crossover distortion and how it can be eliminated in power amplifier? 1. 2. 3. Other than crossover distortion, type B amplifier also has thermal runaway problem. Discuss on this problem and the process of its elimination.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Multistage Transistor Audio Amplifier Circuit; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=LJrL9N9uhkE;License: Standard Youtube License