Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem D2.35P
To determine
The value of voltage gain when potentiometer is set exactly at the middle value.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Design a voltage regulator that will maintain an output voltage of 10 V across a 1k2 load with
an input that will vary between 30 V and 40 V.
Determine the proper value of R, and the maximum current 1z max: (Draw the circuit diagram)
03 For the op-amp eircuit in Figure 2:
a) Determine if the circuit can regulate the output voltage. If not, what change(s)
should be done for it to work as a voltage regulator?
b) Based on your answer in Q3 (a):
i) Derive the output voltage equation.
ii) Find the output voltage.
i) If Vo is 30V, will the emmiter current be less or more? Why?
iv) If Vo is 20V, will the emmiter current be less or more? Why?
V.
(regulated
voltage)
(unregulated
voltage)
R3
2200
40V
Ska
4.7V
1kn
R2
Figure 2
R2
741
DI
R1
D2
In the circuit on the side, the input signal with a peak value of
4 V is applied
case; Plot the graphs V0 (t) and V0 - Vi explaining.
specify required values)
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.arrow_forwardCalculate the worst-case output voltage for the circuit shown if VOS = 2 mV, IB1 = 100 nA, and IB2 = 95 nA. What is the ideal output voltage?What is the total error in this circuit? Is there a better choice for the value of R1? If so, what is the value?arrow_forwardThe current mirror is supposed to faithfully reproduce the input current at its output, but even if the two transistors are designed identically, the Early effect causes problems. Using the circuit in figure below and parameter values from prelab problem #2, estimate the drain voltage of M1. VDD VDD 10K R M1 M2 DFET current mirror Prelab problem2: R1 R3 4.7K 20K Vo R4 R2 10K 470 Assuming VDD=+5V and VSS= -5V, calculate the DC bias conditions for the common-source (and also common-drain) amplifier shown in Figure. Determine VG, VS, VD and ID. For this calculation, assume that Vt = 1.2 and that kn '(W/ L) =300 μ ΑV2arrow_forward
- Q3) For the OP Amp show in figure calculate the O/P voltage when the I/P voltage is 2V and current through 25KN resistor 25 k2 10 k2 iz5 V ww Varrow_forwardQ2 Design a voltage regulator that will maintain an output voltage of 10 V across a 1kN load with an input that will vary between 30 V and 40 V. Determine the proper value of R, and the maximum current 1z max: (Draw the circuit diagram) _max·arrow_forward2. The circuit below is a emitter follower (the output is taken from the emitter and its voltage follows the input voltage). B=100 a. drawn the small signal eq. circuit 9V R1 vo b. Find the Gain vi Zin 100k Zout c. Find Zin and Zout C2 Q1 NPN inf C1 vo Vi1 inf AC 1 1 RL 50 5mAarrow_forward
- II-1) Draw the circuit of a V-I converter and derive an expression for the output current in terms of input voltage, 2) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation.arrow_forward(i) A CdS cell (light sensitive resistor) is configured as shown in Figure Q1 (b) below using four AA batteries for a voltage source (6 V). At dusk, the resistance of the cell rises from a low resistance to above 90 kQ. The cell is used to trigger a comparator that will turn on lights if VOUT is greater than approximately 2 V. What value of R will produce an output voltage of 2 V when the cell resistance is 90 kQ? + 6 V R -O VOUT CdS cell Figure Q1 (b) (ii) Design a comparator to be added to the circuit in Figure Q1 (b). It must switch and provide a +5 V output when the input is greater than 2 V. Redraw the circuit in Figure Q1 (b) with your comparator added clearly labeling all values.arrow_forwarda) Design the circuit of Figure Q2 for a voltage gain of 20 and a power budget of 1mW with VDD = 1.8 V. Assume M₁ operates at the edge of saturation if the input common-mode level is 1 V. Also, assume µnCox = 100 µA/V², µµCox = 50 µA/V², VTH,n = 0.5 V, VTH,p = -0.4 V, In = 0.1 V-¹ and lp = 0.2 V-¹. VDD M3 HEMA A Vin10 M₂ Vin2 P Iss Figure Q2 b) Determine the output impedance formula (no values needed) of the circuit in Figure Q2. Assume gmro >> 1. M Voutarrow_forward
- 2. Design using summing amplifier so that 3V, 2V are given as input voltages and 15 V is obtained at the output. Only one amplifier is allowed to be used. i) Select the resistances accordingly and draw the circuit designing with the mentioned specifications. ii) Explain and show all calculations.arrow_forwardIf the ideal design for op-Amp circuit bli 3 generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to. mVarrow_forwardFor the op-amp shown in the following figure, if R1 = 100 2 and Rf = 1 k2, the overall voltage gain is equal to V₁ a. -10 O b. -1 O c. 11 O d. 9 Rf Voarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Electrical Engineering: Ch 5: Operational Amp (2 of 28) Inverting Amplifier-Basic Operation; Author: Michel van Biezen;https://www.youtube.com/watch?v=x2xxOKOTwM4;License: Standard YouTube License, CC-BY