Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem D2.14P
To determine
To design: The inverting op-amp circuit.
Also, the value of input resistance.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
(a) Illustrate the difference between an operational amplifier's practical equivalent
model and its ideal model and explain how to analyze an op-amp circuit using
the ideal model.
(b) Design a summing operational amplifier having the following channel gains:
Channel 1: AvcL1 = -6
Channel 2: AvcL2 = -9
Channel 3: AVCL3 = -13
Use an external input resistor, R3 = 30KOhms for channel 3, +Vsupply = ±15 V
and +Vsat = 13 V. Draw the circuit and label all components. Use standard
resistance values.
Derive the appropriate equation for an inverting amplifier with op-amp and provide the values of resistances to obtain the gain equal 3 (kvR -> infinity, Vr -> 0)
1. Consider the amplifier circuit shown below. Assuming that the amplifier block is an ideal op-
amp, answer the corresponding questions:
2k
1k
2k
Vo
Vin
2k
10k
2.5V
10V
Draw the entire amplifier using the non-ideal op-amp circuit model and label all attributes.
Assuming that the op-amp is ideal and rail-to-rail, with Vpp and Vss equal to +/- 15.0V
respectively, draw the output voltage curves when sweeping "Vin" from -5V to +5V (
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- From Figure 3, write node-voltage equations: one for each input a. terminal of the op amp. b. The expression for the load current (i.) can be written as a function of the input voltage (V) and the load voltage (v.) iz = Avin + Bv, b.1. What is the expression for A? What should be the condition for R, R, R, and R4, so that B is b.2. zero? (NB: this condition will make i, depend only on v, and not on R.) R4 R3 OA1 R2 R1 RL Vin VL iL Figure 3arrow_forward4kΩ 5k2 3mA . 3ΚΩ 2k2 1kN Determine for the above ideal op-amp circuit, Vo, lo, and the power dissipated in the 2kn resistor. You may assume that the op-amp is ideal and always operates in the linear region.arrow_forward1. Design an inverting amplifier with a gain of 2.5, using an ideal op amp. Use a set of identical resistors from Appendix H. 2. If you wish to amplify signals between -2 V and +3 V using the circuit you designed in part (a), what are the smallest power supply voltages you can use?arrow_forward
- An op-amp with an open-loop gain of 6x105 and Vcc = 15 V has an output voltage of 3 Volts. If the inverting-input voltage is -1.8 microVolts then determine the non-inverting input voltage in microVolts to the single digit decimal place. Do not enter units. For example, if you calculate 3.1x10-6 Volts as your answer then enter 3.1. Similarly, if you calculate 1.872 x10-5 Volts as your answer then enter 18.7 (since this is 18.7 microvolts).arrow_forwardPlease show that gain = -(1-n)/(1+nA) , n = R1/(R1+R2) and compare to gain of ideal op amp. Calculate the input and output impedances, and lastly whats the point of the resistor R1//R2 on the non-inverting input? What would be the best value for this resistor? (pretending it wasn't given that the value is R1/R2).arrow_forward(a) What are the gain and bandwidth of the individual amplifier stages as shown if the op amps have Ao = 105 and fT = 3 MHz? (b) What arethe overall gain and bandwidth of the three-stage amplifier?arrow_forward
- 2) In the op-amp based difference amplifier shown below, the values of R1, R2, R3 and R. are as indicated. i) If V, = 1.6V and V2 = 2.0V, determine the value of Vo. ii) If V; = V2 = 2.0V, and by some fault the value of R3 changes to 25 kQ, determine the value of V,. R = 10 kQ R2 = 100 k. R3 = 10 ko v, MM R4 = 100 kaarrow_forward2K The op amp used in the inverting amplifier circuit is not ideal. In fact, it is an LM741 with the following parameters: v W Rin = 2 MQ, AoL = 200 V/mV, Rout = 200 Q. Determine the gain vo/vi of the op amp circuit. If the gain computed in a is the actual gain, what is the percentage accuracy of the computed gain if the op amp is considered ideal? 4. 1K vo а. b.arrow_forwardConsider the active circuit:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw) in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem.arrow_forward
- Find the current I, in the circuit shown below. Assume op-amp to be ideal? 2k 1k E1karrow_forwardSIM 2.12 For ideal op amps operating with the following feedback networks in the inverting configuration, what closed-loop gain results? For the cases below, please calculate the gain and show in your simulations in LTSpice using an ideal OP-Amp and convince yourself that your calculations and simulated results match. R1 = 10 km, R2 = 20 kn. You can create a schematic and open the example circuit in the "universal opamp" and edit that example circuit and show your voltage simulation results as a screenshot R₂ R₁ 3arrow_forwardDesign a multi-stage amplifier using the specifications below. After the necessary calculations are performed, simulate the circuit in Multisim and make any corrections/changes to the circuit, as necessary. Part I: Amplifier Specifications. • Use no more than three 2N3904 transistors. • The overall amplifier gain should be at least Av = +50 • Input signal should be at • Your circuit load • The input resistance, • The output resistance, . • VCC ≤ 20 volts • The output voltage, Vout is not inverted from the input voltage, Vin.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Number Systems Introduction - Decimal, Binary, Octal & Hexadecimal; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=FFDMzbrEXaE;License: Standard Youtube License