Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 21CQ
To determine
The working point for the soda lime glass.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the relationship between the silica structure and the Bowen's reaction discontinuous series?
A laminated [0/90/0/90]s graphite/epoxy beam is 1 mm thick, is 20 mm wide, and has 0.125 mm thick plies. The lamina properties are E1 = 180 GPa, E2 = 10 GPa, ν12 = 0.28, G12 = 7 GPa Xt = 1700 MPa, Xc = 1400 MPa, Yt = 40 MPa, Yc = 230 MPa
(a) Determine the flexural modulus of the beam
(b) How could the flexural modulus be improved without changing the ply materials, the number of plies, or the ply orientations?
(c) Using the Maximum Stress Criterion for each ply, determine the magnitude of the maximum allowable bending moment that the beam can withstand. Which ply fails first?
9.5 The following thermal bimorph is made of Silicon with a thermal conductivity
k = 130 W/(m°C), Young's modulus E = 200 GPa, Poisson's ratio v = 0.27, and ther-
mal expansion coefficient a = 2.6 × 10-6/°C. It is 1 mm thick with fixed tempera-
tures of 60°C and 10°C, respectively, at the leftmost ends of its hot arm and cold
arm, as shown below. Suppose the bimorph has a uniform internal heat genera-
tion at 100 W/m³, and ignore the effects of convective heat transfer. (1) Determine
the steady-state temperature distribution in the thermal bimorph. (2) Determine
the thermally induced deformation and stresses in the bimorph if the two arms
are fixed on their left ends.
Hot arm
Thot = 60°C
Cold arm
Tcold = 10°C
All dimensions are in millimeters.
6.000-
3.000
2.000
2.000
200
12.000
5.000
3.000
Chapter 9 Solutions
Materials Science And Engineering Properties
Ch. 9 - Prob. 1CQCh. 9 - Prob. 2CQCh. 9 - Prob. 3CQCh. 9 - Prob. 4CQCh. 9 - Prob. 5CQCh. 9 - Prob. 6CQCh. 9 - Prob. 7CQCh. 9 - Prob. 8CQCh. 9 - Prob. 9CQCh. 9 - Prob. 10CQ
Ch. 9 - Prob. 11CQCh. 9 - Prob. 12CQCh. 9 - Prob. 13CQCh. 9 - At temperatures above the equi-cohesive...Ch. 9 - Prob. 15CQCh. 9 - Prob. 16CQCh. 9 - Prob. 17CQCh. 9 - Prob. 18CQCh. 9 - Prob. 19CQCh. 9 - Prob. 20CQCh. 9 - Prob. 21CQCh. 9 - Prob. 22CQCh. 9 - Prob. 23CQCh. 9 - Prob. 24CQCh. 9 - Prob. 25CQCh. 9 - Prob. 26CQCh. 9 - Prob. 27CQCh. 9 - Prob. 28CQCh. 9 - Prob. 29CQCh. 9 - Prob. 30CQCh. 9 - Prob. 31CQCh. 9 - Prob. 32CQCh. 9 - Prob. 33CQCh. 9 - Prob. 34CQCh. 9 - Prob. 35CQCh. 9 - Prob. 1ETSQCh. 9 - Prob. 2ETSQCh. 9 - Prob. 3ETSQCh. 9 - Prob. 4ETSQCh. 9 - Prob. 5ETSQCh. 9 - Prob. 6ETSQCh. 9 - Prob. 7ETSQCh. 9 - Prob. 8ETSQCh. 9 - Prob. 9ETSQCh. 9 - Prob. 10ETSQCh. 9 - Prob. 11ETSQCh. 9 - Prob. 12ETSQCh. 9 - Prob. 9.1PCh. 9 - Prob. 9.2PCh. 9 - Prob. 9.3PCh. 9 - Prob. 9.4PCh. 9 - Prob. 9.5PCh. 9 - Prob. 9.6PCh. 9 - Prob. 9.7PCh. 9 - Prob. 9.8PCh. 9 - Prob. 9.9PCh. 9 - Prob. 9.10PCh. 9 - For silver at a tensile stress of 7 MPa and a...Ch. 9 - For germanium at a tensile stress of 410 MPa and a...Ch. 9 - Prob. 9.13PCh. 9 - Prob. 9.14PCh. 9 - Prob. 9.15PCh. 9 - Prob. 9.16PCh. 9 - Prob. 9.17PCh. 9 - Prob. 9.18PCh. 9 - Prob. 9.19PCh. 9 - Prob. 9.20PCh. 9 - Prob. 9.21PCh. 9 - Prob. 9.22P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Is it true that the effective surface area of kaolinite is limited to external surfaces?arrow_forwardAt room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°Carrow_forwardThe aluminum shell is fully bonded to the brass core, and the assembly is unstressed at a temperature of 78°F. The temperature of the assembly reaches 210°F. Consider only axial deformations. 1 in. Brass core E = 15 x 10° psi a = 11.6 x 10-°F Aluminum shell E = 10.6 x 10° psi a = 12.9 x 10-%°F -2.5 in.- Determine the stress in the brass core. The stress in the brass core is |ksi.arrow_forward
- A single crystal of BCC iron is subjected to tensile stress of 100 MPa along the [001] direction. Which of the two slip systems ((211) –[ 111 ] or (321)–[ 111 ]) is going to yield first?arrow_forwardA ______ test is used to determine how much an elastomer swells when it comes into contact with a fluid.arrow_forwardThe assembly consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 86 GPa, α= 18 × 10−6/°C] has an outside diameter of 33 mm and an inside diameter of 27 mm. The ceramic core [E = 320 GPa, α= 2.5 × 10−6/°C] has a diameter of 27 mm. At a temperature of 15°C, the assembly is unstressed. Assume L = 320 mm. Determine the largest temperature increase Δt that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 65 MPa.arrow_forward
- 6 A steel pipe with a 50 mm outside diameter and a 43.75 'mm inside diameter surrounds a solid brass rod 37.5 mm in diameter as shown. Both materials are joined to a rigid cover plate at each end. The assembly is free to expand longitudinally. The assembly is stress free at a temperature of 27°C. For steel, Young's modulus is 200 GN/m², and the coefficient of linear thermal expansion is 11.7x10-6 1/°C. For brass, Young's modulus is 93.33 GN/m², and the coefficient of linear thermal expansion is 1.872 x 10-5 1/°C. What is the stress in the steel tube when the temperature is raised to 121°C? brass rod (solid) 37.5 mm diameter steel tube 50 mm outside diameter 43.75 mm inside diameterarrow_forwardVMA is an indication of film thickness on the surface of the aggregate. True Falsearrow_forwardTwo silicon wafer sizes are to be compared: a 6.0-in wafer with a processable area = 5.85-in diameter circle and a 12.0-in wafer with a processable area = 11.75-in diameter circle. The IC chips in both cases are square with 0.50 in on a side. Assume that the cut lines (streets) between chips are of negligible width. What is the percent increase in (a) processable area on the wafer, and (b) number of chips on the wafer compared to the 200% increase in wafer diameter?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning