Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 50, Problem 6RQ
Properly installed roof curbs will reduce the chances of
A. leaks.
B. noise transmission.
C. Both A and B are correct.
D. Neither A nor B is correct.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A technician is inspecting a vehicle and finds
the upper radiator hose is collapsed, and the
cooling system pulled into a vacuum when
cold. Technician A states that a leak in the
surge tank could be the cause. Technician B
states that the radiator cap is most likely
defective. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
4.a. You can usually check for a leak in a vacuum system by looking at or feelingA. at the vacuum gauge at the vacuum pump.B. for signs of dirt on the piping.C. at the exhaust of the vacuum pump.
4.b. When a pneumatic solenoid fails, the failure is normally due to aB. weak pilot.C. bad spool.D. ripped seal.
Technician A says that coolant hoses should
be squeezed to check for hardening or
softening. Technician B says that coolant
hoses should be visually inspected for
swelling and cracks. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Chapter 50 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 50 - Which of the following is true regarding the...Ch. 50 - Which process would best represent the opposite of...Ch. 50 - Mixed air is best described as the combination of...Ch. 50 - Which of the following should be taken into...Ch. 50 - A bonded roof is one that has A. reinforced steel...Ch. 50 - Properly installed roof curbs will reduce the...Ch. 50 - When rigging a unit to the roof, what minimum...Ch. 50 - What is the acceptable method for communicating...Ch. 50 - Prob. 9RQCh. 50 - Prob. 10RQ
Ch. 50 - The most efficient way to establish the best...Ch. 50 - Free-cooling can be accomplished if the
A....Ch. 50 - Prob. 13RQCh. 50 - Prob. 14RQCh. 50 - Explain why the outside air damper is typically...Ch. 50 - Briefly explain the purpose of ASHRAE Standard 62.Ch. 50 - Explain the concept of demand control ventilation.Ch. 50 - Explain how carbon dioxide levels can be used to...Ch. 50 - Describe the blowers used on VAV systems.Ch. 50 - A cooling-only VAV box has all of the following...Ch. 50 - Which of the following is true regarding a reheat...Ch. 50 - Variable refrigerant flow systems sense the...Ch. 50 - The acronym PID stands for ______, _____, and...Ch. 50 - Explain the main benefit of a heat-recovery VRF...Ch. 50 - The pump on a dry cooler can direct water to...Ch. 50 - During low ambient conditions, the space cooling...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which beaker best illustrates what happens when the following acids are dissolved in water?a. HNO2b. HNO3c. HC1d. HFe. HC2H3O2arrow_forwardCleaning a machine with compressed air is a general safety precautions considered while working in a workshop. Select one: True Falsearrow_forwardproper FBD and solution pleasearrow_forward
- d. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make sure the connections are clean and tight relevant to a. Breaking system b. Ignition system c. Ventilation system d. Combustion system 20. The required gap in ignition system between---------- a.-4 to 5 b.-0.4 to 5 c.-0.4 to 0.5 d.-4 to 0,5 |21. Which of the following is the fouled of spark plug a. Soot b. Oil c. Over heated d. All of the above |22.The suitable thread of spark plug for heavy engine is a. M19 b. M18 c. M15 d. M16 23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to four kilograms per square inch. a. True b. False 24. Start the engine and evaluate its performance refers to a. Weekly Maintenance b. Annually Maintenance c. Daily Maintenance d. None of them 25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to a. Weekly Maintenance b. Annually…arrow_forwardList and explain five ladder use safety rules.arrow_forwardTwo techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Pressure regulators are being discussed. Technician A says they are located in the fuel rail. Technician B says they are located on the fuel rail. Who is correct? a. A only b. B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that when installing an oil filter, you should tighten it with a filter wrench to prevent it from falling off. Technician B says that oil filters should only be installed by hand. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardneed correct and urgentarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License