Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 1.3CS
A wide spectrum of coatings and surface treatments have been applied to fishhooks. These have included clear lacquer; platings of gold, tin, nickel, and other metals; Teflon; and a variety of coloration treatments involving chemical treatments, thermal oxides, and others. Select several possible surface treatments and discuss how they might be applied while: (a) maintaining the sharpness of the point and barbs and (b) preserving the
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Heat treatments optimize the performance and extend the life of gears in service by altering their chemical, metallurgical, and physical properties. To what extent do you agree or disagree with this statement? Support your opinion with FOUR (4) relevant examples of suitable process to prevent such a gear failure
25. Describe and explain the use of carburising as a thermochemical treatment and outline the principles of gas carburising, giving brief details of the resulting surface treatment properties.26. Describe and explain the principles of anodising as an electrochemical coating process, highlighting the use of hard anodising, and give brief details of the resulting coating properties.
answer all parts
A pipe can be manufactured as (a) seamless (cold rolled and extruded) or (b) hot rolled and welded. (i) Describe the process for manufacturing each type of pipe: (a) Seamless (cold rolled and extruded) pipe; (b) Hot rolled and welded pipe. (ii) Why might a cold rolled seamless pipe be better suited to drilling operations than a hot rolled and welded pipe?
A particle reinforced composite (containing flakes) has particles evenly distributed throughout the matrix where the rule of mixtures applies. (i) State THREE effects that a larger volume of carbon particles within the matrix produces.
A drill bit is a cutting tool on the end of a rotary subsea drill. A Thermally Stable Polycrystalline (TSP) drill bit can be used to drill a subsea well. TSP bits are man-made polycrystalline structures consisting of a multitude of synthetic diamond crystals sintered together at high pressure and temperature, used to aid cutting into hard rock formations. (i) Describe THREE reasons why this type…
Chapter 4 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 4 - What kind of questions can be answered by...Ch. 4 - Prob. 2RQCh. 4 - Supplement the examples provided in the text with...Ch. 4 - Prob. 4RQCh. 4 - What three primary variables are generally...Ch. 4 - Use the pressure–temperature diagram for water...Ch. 4 - Prob. 7RQCh. 4 - What form of equilibrium phase diagram is most...Ch. 4 - What is a cooling curve?Ch. 4 - Prob. 10RQ
Ch. 4 - Prob. 11RQCh. 4 - Prob. 12RQCh. 4 - Prob. 13RQCh. 4 - What types of changes occur upon cooling through a...Ch. 4 - Prob. 15RQCh. 4 - What is a tie�line? For what types of phase...Ch. 4 - What points on a tie�line are used to determine...Ch. 4 - Prob. 18RQCh. 4 - What is a cored structure? Under what conditions...Ch. 4 - What is the difference between a cored structure...Ch. 4 - Prob. 21RQCh. 4 - Prob. 22RQCh. 4 - Prob. 23RQCh. 4 - Prob. 24RQCh. 4 - For the various three�phase reactions, what does...Ch. 4 - Prob. 26RQCh. 4 - Prob. 27RQCh. 4 - Prob. 28RQCh. 4 - Prob. 29RQCh. 4 - Prob. 30RQCh. 4 - Prob. 31RQCh. 4 - Prob. 32RQCh. 4 - Prob. 33RQCh. 4 - Prob. 34RQCh. 4 - Prob. 35RQCh. 4 - Prob. 36RQCh. 4 - Prob. 37RQCh. 4 - What is carbon equivalent, and how is it computed?Ch. 4 - Prob. 39RQCh. 4 - Prob. 40RQCh. 4 - Prob. 1PCh. 4 - Prob. 2PCh. 4 - Prob. 3PCh. 4 - Consider the manufacture of a fishhook beginning...Ch. 4 - If a stainless steel were to be used, what type of...Ch. 4 - A wide spectrum of coatings and surface treatments...Ch. 4 - Prob. 1.4CSCh. 4 - Prob. 2.1CSCh. 4 - Prob. 2.2CSCh. 4 - Prob. 2.3CSCh. 4 - Prob. 2.4CS
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the Mannesmann milling process? Why is the Mannesmann piercing process not capable of producing extremely long lengths of seamless tubing?arrow_forward(a) An engineer would like to drill a square hole of 20 mm x 20 mm with depth of 25 mm on a layered structure of natural fibre-reinforced polymer composite. He encountered delamination problem in the workpiece (Figure 3) when he used conventional cutting tool to drill the hole. Instead of using conventional machining process, discuss ONE suitable advanced machining process that can be applied for this machining purpose and predict TWO possible limitations for the selected process. Cutting Tool Delamination Composite Material Figure 3. Delamination of the composite material.arrow_forwardList three general categories of surface treatment that can increase fatigue life, and provide one example of a specific process for each category.arrow_forward
- Which three of the following are names given to the three regions in the typical wear growth curve: (Choose three answers) temperature region diffusion region failure region 0000000 accelerated wear region break-in period steady-state wear abrasion regionarrow_forwardWhat manufacturing processes do you think were applied? Or what information be needed about the fabrication of this piece?arrow_forwardIn the electrochemical machining of an iron surface with 10 mm×10 mm in cross-section, the NaCl in water is adopted as electrolyte. The gap between the tool and workpiece is 0.2 mm. The supply voltage is 12 V DC. The specific resistance of the electrolyte is 3Ωcm. (For iron, valency=2, atomic weight=55.85, and density=7860 kg/m3). Please estimate the material removal rate and the tool feedrate.arrow_forward
- Ranking metal shaping processes by kg carbon footprint (per kg of stuff produced) which of the following is the correct ranking (least carbon footprint to most)? Extrusion, Forging, Wire drawing, Casting, Vapour Deposition Methods, Powder Forming Forging, Casting, Extrusion, Powder Forming, Wire drawing, Vapour Deposition Methods Casting, Forging, Extrusion, Wire drawing, Powder Forming, Vapour Deposition Methods Casting, Extrusion, Forging, Wire Drawing, Powder Forming, Vapour Deposition Methodsarrow_forwardShow your correct solution to this pronblem. ASAP! Thanks!arrow_forward2. In the electrochemical machining of an iron surface with 20 mm× 20 mm in cross-section, the NaCl in water is adopted as electrolyte. The gap between the tool and workpiece is 0.2 mm. The supply voltage is 15 V DC. The specific resistance of the electrolyte is 2 Q cm. (For iron, valency=2, atomic weight=55.85, and density=7860 kg/m³). Please estimate the material removal rate and the tool feedrate.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
MECH MINUTES | SHAFTS PT. 2: MATERIAL & SURFACE TREATMENT SELECTION | MISUMI USA; Author: MISUMI;https://www.youtube.com/watch?v=jWRA0jhoiRs;License: Standard Youtube License