Concept explainers
A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. Knowing that h = 12 in. and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.
Fig. P17.97
Trending nowThis is a popular solution!
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Introduction to Heat Transfer
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
Fluid Mechanics Fundamentals And Applications
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Fundamentals of Heat and Mass Transfer
- 17.105 A 1.25-oz bullet is fired with a horizontal velocity of 950 ft/s into the 18-lb wooden beam AB. The beam is suspended from a collar of negligible weight that can slide along a horizontal rod. Neglecting friction between the collar and the rod, determine the maximum angle of rotation of the beam during its subsequent motion. B Fig. P17.105 4 ftarrow_forward17.86 A 65-lb uniform circular plate of radius r is supported by a ball- and-socket joint at point A and is at rest in the vertical xy plane when a bul- let weighing 0.03 lb is fired with the velocity vo -(700 ft/s)k and hits the 28 in., determine (a) the plate at point C. Knowing that r = 16 in. and h angular velocity of the plate immediately after the bullet becomes embed- ded. (b) the impulsive reaction at point A, assuming that the bullet becomes embedded in 1.1 ms. Fig. P17.86 y Barrow_forwardA large 3-lb sphere with a radius r = 3 in. is thrown into a light basket at the end of a thin, uniform rod weighing 2 lb and length L= 10 in. as shown. Immediately before the impact, the angular velocity of the rod is 3 rad/s counterclockwise and the velocity of the sphere is 2 ft/s down. Assume the sphere sticks in the basket. Determine after the impact (a) the angular velocity of the bar and sphere, (b) the components of the reactions at A.arrow_forward
- 3. (17.21) A collar at point C with a mass of 1 kg is rigidly attached at a distance d = 300 mm from the end of a uniform slender rod AB. The rod has a mass of 3 kg and has a length of L = 600 mm. Knowing that the rod is released from rest in the position shown, determine the angular velocity of the rod after it has rotated through 90°. Notes: Ignore rotation of the collar since its dimensions are negligible. The controidal moment of inertia of the rod is I = m[² 12 L d Position 1 Position 1 B B A Position 2 L A' ctivate Windowsarrow_forward196 A uniform slender rod AB is at rest on a frictionless horizontal table when end A of the rod is struck by a hammer which delivers an im- that is perpendicular to the rod. In the subsequent motion, determine distance b through which the rod will move each time it completes a full revolution. Fig. P17.96 Barrow_forward5. Fig. 3 shows the overhead view of a uniform thin rod of length I and mass M that can rotate freely about a fixed axis on a horizontal surface. The rod is at rest initially with moment of inertia MI². A bullet of mass m is fired towards one end of the rod with initial velocity v. After piercing the rod, the bullet's velocity is reduced to v. The angular velocity of the rod after being shot through is ( ) 3mv А. 2ML 7mv В. 4ML overhead view mv C. MI Fig 3 D. 5mv 3MIarrow_forward
- 17.48 A 6-lb sphere of radius r = 5 in. with an initial clockwise angu- lar velocity wo = 90 rad/s is placed in the corner formed by the floor and a vertical wall. Knowing that the coefficient of kinetic friction is 0.10 at A and B, determine the time required for the sphere to come to rest. A Fig. P17.47 and P17.48arrow_forwardA bullet of mass m is fired with a horizontal velocity v0 and at a height h = ½ R into a wooden disk of much larger mass M and radius R . The disk rests on a horizontal plane and the coefficient of friction between the disk and the plane is finite. (a) Determine the linear V1 and the angular velocity w1 of the disk immediately after the bullet has penetrated the disk. (b) Describe the ensuing motion of the disk and determine its linear velocity after the motion has become uniform.arrow_forward14 in. 18 in. VB 1500 ft/s -18 in. A 0.05-lb bullet is fired into the side of a 20-lb square panel which is initially at rest. Determine a) the angular velocity of the panel immediately after the bullet becomes embedded and b) the impulsive reaction at A, assuming that the bullet becomes embedded in 0.0006 s. Barrow_forward
- Sphere A Mass m and radius r rolls without slipping with a velocity V1 on a horizontal surface when it hits squarely an identical sphere B that is at rest. Denoting by μk the coefficient of kinetic friction between the spheres and the surface, neglecting friction between the spheres, and assuming perfectly elastic impact, determine (a ) the linear and angular velocities of each sphere immediately after the impact, (b) the velocity of each sphere after it has started rolling uniformly.arrow_forwardA 1.8-lb javelin DE impacts a 10-lb slender rod ABC with a horizontal velocity of v0 = 30 ft/s as shown. Knowing that the javelin becomes embedded into the end of the rod at point C and does not penetrate very far into it, determine immediately after the impact (a) the angular velocity of the rod ABC (b ) the components of the reaction at B. Assume the javelin and the rod move as a single rigid body after the impact.arrow_forwardDetermine the height h at which the bullet of Prob. 17.108 should be fired (a) if the disk is to roll without sliding immediately after impact, (b) if the disk is to slide without rolling immediately after impact.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY