Imagine that a small hole is opened in the container wall near the bottom of each layer.
1. Predict what will happen to the water near each hole. Explain.
2. Check your prediction by observing the demonstration. Record your observations. (Asketch may be helpful.)
What do your observations suggest about: (1) the existence of horizontal forces on thethree layers of water in pan A? (2) the relative magnitudes of the horizontal forces onthe three layers?
If necessary, revise your free-body diagrams in part A so that they are consistent withyour answers.
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Tutorials in Introductory Physics
Additional Science Textbook Solutions
Applied Physics (11th Edition)
Essential University Physics (3rd Edition)
Sears And Zemansky's University Physics With Modern Physics
The Cosmic Perspective Fundamentals (2nd Edition)
Essential University Physics: Volume 2 (3rd Edition)
The Cosmic Perspective (8th Edition)
- Show your complete solution and round-off your finalanswer in the nearest thousandths (3 decimals).a. How much pressure will be measure at the bottom of thewater tank with a height of ℎ = 2? and a cross sectionalarea of ? = 785.398 ??2?b. How much pressure will be measure at the middle of thewater tank with a height of ℎ = 2? and a cross sectionalarea of ? = 785.398 ??2?c. If the diameter of the tank in the previous questions wereincreased twice but it height remain the same, what willhappen to pressure (a) at the middle of the tank and (b) atthe bottom of the tank?arrow_forward1.) Is liquid volume directly proportional to temperature? Explain briefly 2.) Is Charles Law applicable to liquids?arrow_forwardShow your complete solution and round-off your final answer in the nearest thousandths (3 decimals). 1. How much pressure will be measure at the bottom of the water tank with a height of 2m and a cross sectional area of 785.398mm²? 2.How much pressure will be measure at the middle of the water tank with a height of 2m and a cross sectional area of 785.398mm²? 3.Ifthe diameter of the tank in the previous questions were increased twice but it height remain the same, what will happen to pressure (a) at the middle of the tank and (b) at the bottom of the tank?arrow_forward
- The question I need to be answered is 1B (the second picture). I included the first question because some of the information from it is the same. Thanks!arrow_forwardSuppose a cube 1-cm long on each side were scaled up to a cube 10-cm on each edge a) what would be the volume of the scaled up cube? B) what would be its cross-sectional surface area? C) what is the total surface area? Show your work, formulas and calculations to support your results be sure to include the appropriate units for volume and areaarrow_forwardI need help on this question. Explain how you got your answers and why they seem reaarrow_forward
- Please put all the equations into the pictures and we’ll explained so I can understand:).arrow_forwardPart (a) Derive an expression for the sensor height, h, above the horizontal tank bottom as a function of L, d and O. h= B) Use logic to deduce the value, in degrees, of the angle A when the fuel tank is full. No computation is required. θfull= Part (c) Calculate the angle, in degrees, associated with a half-full fuel tank. Part (d) Note that the arm is longer than the tank is deep, I > d. What angle, in degrees, is associated with an empty fuel tank?arrow_forwardI need more detail about my answer, so watch the professor's comment and write your solution more detail. 2. A cylindrical object—with radius R, length L, and density ??—sits on a scale at the bottom of vat of fluid with density??.a. Draw and label a free body diagram for the object. (Don’t forget to set up a coordinate system and to label the acceleration info. Also, be sure to use the gridlines to help you draw arrows that show the correct directions and relative magnitudes of the forces. Finally, be sure to label your forces clearly to indicate the types of forces.)b. Use Newton’s 2nd Law to derive an expression for the reading on the scale.arrow_forward
- In the example shown in the figure, (Figure 1) the "container" is a cylinder whose volume changes as the piston slides in or out. Suppose a gas is confined within the cylinder. The pressure of the gas is p, and the area of the cylinder is A. Consider the work done as the gas expands, pushing the piston to the right. Call the small distance that the piston moves Δx. a)What force F does the gas exert on the piston? (Note that the positive x axis is to the right in the figure.) Express the force in terms of p, A, and any constants. b)If the piston moves a small distance Δx, what is W, the work done by the gas? Express the work done by the gas in terms of Δx and other given quantities. c)What is ΔV, the increase in volume of the gas? Express the increase in volume in terms of Δx and other given quantities.arrow_forwardA cylindrical steel tank with a diameter of 20.0 cm, a length of 150.0 cm, and an overall mass of 150.0 kg is accidently dropped into a lake. What is the cylinder's density in g/cm3? Will it sink or float? Pure water has a density of 1 g/cm3. Show your work.arrow_forwardA student observes air bubbles on their metal cylinder when measuring the density. How do you think the presence of bubbles might affect the students' final calculated density (i.e. would it have been to low, too high, or unchanged and why)?arrow_forward