Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
thumb_up100%
Chapter 8, Problem 1RQ
To determine
Identify if the component is normally open or normally closed when the component is to be used for the function of start.
Expert Solution & Answer
Explanation of Solution
There are circumstances where it is desirable to have more than one start/stop push button when operating a motor.
When a component is used for the function of start then the component is generally open and is connected parallel to the existing start button. If either of the start button is pressed, the circuit will be completed and the coil will be energized.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Question#01 (Serial number=26.2)
Please provide justified answer for all three sub parts asap to get a upvote
Probid solution with all steps and details for upvote
What is the process of locating the instantaneous center?
Chapter 8 Solutions
Understanding Motor Controls
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. Following are the sequence of operations 1. The operation is to be started using a push button (use the label START PB). Include a stop push button (use the label STOP PB) to stop the process at any time. (Use Memory ON circuit) 2. An acknowledgement signal (S1- Limit switch) is required when the piston is fully extended, to ensure that the work piece has been tipped onto the belt. 3. The extension should be slower than the retraction (use flow control valve) 4. The return stroke should be automatic. a. Design the Electro- Hydraulic Circuit with proper labeling. Include the components required b. Draw the Displacement -step diagram & Displacement -time diagram (include Cylinder, START PB, STOP PB, DCV and S1)arrow_forwardHow is across-the-line starting accomplished?arrow_forwardHow to perform zero point reset?arrow_forward
- 4. Describe two type of starting system principles and draw the basic starting circuitarrow_forwardWhen programming in Boolean, what statement should be used to connect components in series?arrow_forwardThe type of spindle unit shown in figure is: Air or liquid cooling Select one: Release mechanism Tool clamp Motor Belt drive Gearbox drive O Coupled drive Coupling Spindle None of the above Direct drivearrow_forward
- What is system?arrow_forwardFor a given frame size, a three phase machines gives a higher output than a single phase machine. Select one: True Falsearrow_forwardElectro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing the start pushbutton makes 5 cycles. After making 5 cycles lamp is energized for 3 secs. Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Then retract. Cylinder A retract.arrow_forward
- 1. In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: activate the direction control valve to start the process, Cylinder A and Cylinder B clamps the workpiece and then activate the second directional control valve to drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B A+ B+ sensors Figure 1: Drilling Process а) Design the Hydraulic Circuit with proper labeling. Include the allocation list and the components required b) Draw the functional diagram/step diagramarrow_forwardWhat is an ATC?arrow_forwardWhat is a couplingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning