Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 12R
Using Table 7-4, answer the following:
a . Oxygen pressure for cutting 1/4-in. (6-mm)-thick metal
b. Acetylene pressure for cutting 1-in. (25-mm)-thick metal
c. Tip cleaner size for a tip for 2-in. (51 -mm)-thick metal
d. Drill size for a tip for 1/2-in. (13-mm)-thick metal
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What will be the notation of throat length of a fillet weld
Name
Part 11
1. What does the following welding symbol indicate?
100
(5)
c-d
GTAW
4. Describe the following weld(s).
ASW
2. Describe the weld(s) indicated by the following welding symbol.
d
3. Sketch in the weld(s) indicated by the welding symbol.
b-c
GMAW
000000
w
a.
C.
d.
e.
b.
b.
C.
d.
e
C.
d
a.
b.
e.
5. Sketch the welding symbol describing the following spot weld(s).
375
18 Spot, Seam, and Projection Welds 255
0.31
Copyright Goodheart-Wilcox Co., Inc. May not be reproduced or posted to a publicly accessible website
Diagram:
Given the hook-up drawing, list all the equipment, tools and
materials that are needed in installation.
INST.
PIPING
1-
*1
INST.
PIPING
Chapter 7 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 7 - Using Table 7-1, list the six different fuel gases...Ch. 7 - What metals can be cut with the oxyfuel gas...Ch. 7 - What other term is used to refer to the OFC...Ch. 7 - What is a combination welding and cutting torch?Ch. 7 - State one advantage of owning a combination...Ch. 7 - State one advantage of owning a dedicated cutting...Ch. 7 - What is a mixing chamber? Where is it located?Ch. 7 - Define the term equal-pressure torch. How does it...Ch. 7 - How does an injector-type mixing chamber work?Ch. 7 - State the advantages of having two oxygen...
Ch. 7 - Why are some copper alloy cutting tips...Ch. 7 - Using Table 7-4, answer the following: a . Oxygen...Ch. 7 - What determines the amount of preheat flame...Ch. 7 - What can happen if acetylene is used on a tip...Ch. 7 - Why are some propane and natural gas tips made...Ch. 7 - What types of tip seals are used with cutting...Ch. 7 - If a cutting tip sticks in the cutting head, how...Ch. 7 - How can cutting torch tip seals be repaired?Ch. 7 - What is used to reduce the high cylinder or system...Ch. 7 - What do the two pressure gauges on a regulator...Ch. 7 - Why must the gas pressure be released and the...Ch. 7 - What should be done if the torch flashes back?Ch. 7 - What is the purpose of a reverse flow valve?Ch. 7 - Why must the reverse flow valve and the flashback...Ch. 7 - How can a hose be checked for leaks?Ch. 7 - Why is the oxygen valve turned on before starting...Ch. 7 - Why does the preheat flame become slightly...Ch. 7 - What causes the tiny ripples in a hand cut?Ch. 7 - Why is a slight forward torch angle helpful for...Ch. 7 - Why should cans, drums, tanks, or other sealed...Ch. 7 - Why is the torch tip raised as the cutting lever...Ch. 7 - Why are the preheat holes not aligned in the kerf...Ch. 7 - Sketch the proper end shape of a soapstone that is...Ch. 7 - What are two methods you can use to determine what...Ch. 7 - What is the best way to set the oxygen pressure...Ch. 7 - Why is it important to have extra ventilation...Ch. 7 - What factors regarding a cut can be read from the...Ch. 7 - What is hard slag?Ch. 7 - Why is it important to make good-quality cuts?Ch. 7 - When using an ordinary welding table, what can be...Ch. 7 - Describe the methods of controlling distortion...Ch. 7 - List three things that can become a problem when...Ch. 7 - How does cutting small-diameter pipe differ from...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Using Table 17-3, Table 17-5, and Table 17-6, list the filler metals for the following metals. a. 1020 low carbon steel b. 309 stainless steelarrow_forwardUse Table 31-5 to determine the largest tip orifice size (drill number) that could be used with an acetylene cylinder containing 175 cu ft (4956 L).arrow_forwardUsing Table 9-1, what material can be cut with nitrogen?arrow_forward
- Referring to Table 28-5, what stainless steel filler metal would be selected for welding a. 304L stainless steel to 314 stainless steel? b. 321 stainless steel to 348 stainless steel? c. 316 stainless to mild steel?arrow_forwardAccording to Table 15-4, what is the range of volts and amps for E70T-11 0.035 diameter filler wire?arrow_forwardWhat dimensions can be given for a plug weld?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License