Interpretation:
a) To determine the relation between dc bias current, current through array, and current through load resistance.
b) To show that
c) To relate
d) To show
e) To write the equation derived in part d) in standard form of
Concept Introduction:
A Josephson Junction consists of two superconductors which are coupled by a week connection of insulators, a weakened superconductor, or a semiconductor.
Josephson Junctions are superconducting devices, which can produce voltage oscillations of very high frequency in the range of
If a Josephson junction is connected to a dc current source so that a non-zero current
When the current
Want to see the full answer?
Check out a sample textbook solutionChapter 4 Solutions
Nonlinear Dynamics and Chaos
- This question refers to a 2 by 2 nonlinear dynamical system. Please show all work for every part. a) compute all steady state solutions and determine their stability b) Confirm your analysis by plotting the long term solutions using specific values of λ, a and c. This is an unsolved example from lecture notes.arrow_forward5. Find the critical point or points for eorh of the following autonomous system. Then match each pair with its phase portrait on the next page. dx = 2x - 2y - 4 and =x+ 4y + 3 dt dt Critical point(s): Matching graphic: FIGURE 6.1. Thedict the usedarrow_forwardInteraction of two species of squirrels fiercely competing for the same ecological niche on an island is described by Lotka-Volterra-Gause equations dN1 N1(2 – N1 – 2N2) = f(N1, N2), dt (1) dN2 N2(3 – N2 – 3N1) = g(N1, N2), dt where N1 = N1(t) and N2 = N2(t) are the population densities of the competing species.arrow_forward
- Find general solutions of the systems in Problem Attached. Use a computer system or graphing calculator to construct a direction field and typical solution curves for the given system.arrow_forwardFor the following two-population system, first describe the type of x- and y-populations involved (exponential or logistic) and the nature of their interaction-competition, cooperation, or predation. Then find and characterize the system's critical points (as to type and stability). Determine what nonzero x- and y-populations can coexist. Finally, construct a phase plane portrait that enables you to describe the long-term behavior of the two populations in terms of their initial populations x(0) and y(0). dx dt dy dt=xy-4y = 5xy-10x CICCES Describe the type of x- and y-populations involved. Select the correct choice below. OA. The populations involved are naturally declining populations in competition. OB. The populations involved are naturally growing populations in cooperation. OC. The populations involved are naturally declining populations in cooperation. OD. The populations involved are naturally growing populations in competition.arrow_forward1. Find the critical points and determine their nature for the system x = 2y + xy, y=x+y. Hence sketch a possible phase diagram.arrow_forward
- Suppose a 32-pound weight stretches a spring 2 feet. If the weight is released from rest at the equilibrium position, find the equation of motion x(t) if an impressed force f(t) = 24t acts on the system for 0 st< 5 and is then removed (see Example 5 in Section 7.3). Ignore any damping forces. (Use g = 32 ft/s2 for the acceleration due to gravity.) x(t) = ftarrow_forwarda. Find the most general real-valued solution to the linear system of differential equations (see image) b. In the phase plane, this system is best described as a... A. source / unstable nodeB. sink / stable nodeC. saddleD. center point / ellipsesE. spiral sourceF. spiral sinkG. none of thesearrow_forwardHW -3 1. An article in Solid State Technology ("Orthogonal Design for Process Optimization and Its Application in Plasma Etching," May 1987, pp. 127–132) describes the application of factorial designs in developing a nitride etch process on a single-wafer plasma etcher. The process uses C2F6 as the reactant gas. It is possible to vary the gas flow, the power applied to the cathode, the pressure in the reactor chamber, and the spacing between the anode and the cathode (gap). Several response variables would usually be of interest in this process, but in this example we will concentrate on etch rate for silicon nitride. Perform an appropriate experiment to characterize the performance of this etching process with respect to the four process variables. Design Factor Gap A Pressure C;F, Flow Power Level (сm) (m Torr) (SCCM) (W) Low (-) 0.80 High (+) 1.20 275 325 450 125 550 200 2. To illustrate the use of a one-half fraction, consider the plasma etch experiment. An article in Solid State…arrow_forward
- Advanced Engineering MathematicsAdvanced MathISBN:9780470458365Author:Erwin KreyszigPublisher:Wiley, John & Sons, IncorporatedNumerical Methods for EngineersAdvanced MathISBN:9780073397924Author:Steven C. Chapra Dr., Raymond P. CanalePublisher:McGraw-Hill EducationIntroductory Mathematics for Engineering Applicat...Advanced MathISBN:9781118141809Author:Nathan KlingbeilPublisher:WILEY
- Mathematics For Machine TechnologyAdvanced MathISBN:9781337798310Author:Peterson, John.Publisher:Cengage Learning,