Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 18.42SP
Using the AISC column equations, select the lightest W10 shape for a column subjected to an axial compressive load of 280 kips. The unbraced length of the column is 18 ft and the ends are pinned. The steel is ASTM A992.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A circular bar is used as a column carrying a load of 8500 lb with pinned ends. The length of the bar is 50 in. Use SAE 4140 OQT1000 steel and design factor of 3.0.
(E for steel = 30,000 ksi)
Determine the required diameter of the column
D =
in
(Must show calculations and attach the worksheets in the last question)
A 5 ft column is made from 2024-T4 Aluminum. Column has a square cross section of 2 in x 2 in.
Both ends of the column are pinned. Calculate the critical load (Pcr).
Note: I am having trouble understanding what the Module of Elasticity is for 2024-T4 Aluminum.
A circular hollow column has an external diameter of 1.5 m and a wall thickness of 0.25 m. Both ends are fixed and it is 20.8
m high. Calculate the critical load in kN if Youngs Modulus for the column material is 200 GPa.
Chapter 18 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - A pin-connected axially loaded compression member...Ch. 18 - Prob. 18.4PCh. 18 - Plot a curve showing the relationship of feversus...Ch. 18 - A W1222 structural steel wide-flange section is...Ch. 18 - Prob. 18.7PCh. 18 - Calculate the allowable axial compressive load for...Ch. 18 - A W20059 structural steel wide-flange section is...Ch. 18 - Use Euler’s formula and a factor of safety of 2.5...
Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - For Problems 18.11 through 18.17, unless otherwise...Ch. 18 - Prob. 18.17PCh. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.18 through 18.21, use the...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26 assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For Problems 18.22 through 18.26, assume normal...Ch. 18 - For the following computer problems, any...Ch. 18 - For the following computer problems, any...Ch. 18 - Calculate the Euler buckling load for an axially...Ch. 18 - 18.32 Calculate the Euler buckling load for an...Ch. 18 - 18.33 A structural steel shape of ASTM A992 steel...Ch. 18 - Calculate the Euler buckling load for a...Ch. 18 - 18.35 Rework Problem 18.34 assuming that the...Ch. 18 - 18.36 A built-up steel column is made by welding a...Ch. 18 - A 2-in-diameter standard-weight steel pipe is used...Ch. 18 - A structural steel column is 30 ft long and must...Ch. 18 - 18.39 Compute the allowable axial compressive load...Ch. 18 - 18.40 Determine the allowable axial compressive...Ch. 18 - 18.41 Using the AISC column approach, compute the...Ch. 18 - Using the AISC column equations, select the...Ch. 18 - Select the lightest extrastrong steel pipe section...Ch. 18 - 18.44 Compute the required diameter of a steel...Ch. 18 - 18.45 A 19-mm-diameter steel rod is 350 mm in...Ch. 18 - 18.46 A pin-connected linkage bar is 16 in. long...Ch. 18 - Prob. 18.47SPCh. 18 - Prob. 18.48SPCh. 18 - Prob. 18.49SPCh. 18 - Prob. 18.50SPCh. 18 - Prob. 18.51SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the following service loads: dead load, D = 20 k, live load, L = 35 k, snow load, S = 25 k, and earthquake, E = 50 k. The connection is two lines of bolts through the flange with three 3/4-in Ø bolts in each line spaced at 3 in on center. Use A992 Grade 50 steel. Neglect block shear.arrow_forward.A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter. The column length is 1.2 m. Calculate the crippling load using Johnson’s Parabolic formula. Take modulus of elasticity and yield strength as 206 GPa and 330 MPa, respectively. Assume one end is hinged and the other end fixed.218212 N176745 N930094 N263252 Narrow_forwardPart A The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eigure 1) If the wire has a diameter of 4.8 mm, determine how much t stretches when the distributed load acts on the strut. Express your answer three to significant figures and include the appropriate unita. ? SAn = Value mm Figure 3AANm 27 marrow_forward
- A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Diarrow_forwardTo calculate the maximum axial loads for a column based on yielding and buckling about both axes, and allowing for factors of safety. The critical load P for buckling of a column depends on the vertical distance between supports and how the column is connected to those supports. The length L in the T'EI formula Per =- is the distance between points of zero moment. For a pin- L2 supported column, this is the full height of the column. For a column that is not pinned at both ends, the points of zero moment are not at the supports. The equation for the critical load can be modified to use an effective length Le = KL, where K depends on the support conditions. For a column fixed at both ends, K = 0.5. For a column fixed at one end and pinned at the other, K = 0.7 (Figure 1). The equation for the critical load then becomes ’EI Pa (KL)²arrow_forward1. Construct a critical end-load intensity against slenderness ratio graph for a range of pinned columns made from a material having a Young's Modulus of 200 GPa and a yield stress of Use slenderness ratios from 0 to 300. 30ОMPа.arrow_forward
- A hollow short compression member, of normalized cast steel where Su = 65 ksi, is to support a load of 1,500 kips with a factor of safety of 8.0 based on the ultimate strength. Determine the outside and inside diameters if Do =2Di.arrow_forwardSelect the lightest WT4 shape to be used as a 20 ft long tension member to resist the of dead load, D=40 k, live load, L=60 k, snow load, PS=25 k, and earthquake, E=110 k. The connection is two lines of bolts through the flange with three 3/4-in ∅ bolts in each line spaced at 3 in on center. Use A992 Grade 50 steel. Neglect block shear.arrow_forwardSelect the lightest W shape that will act as a column of 7 m long with both end hinged and support an axial load of12KN with the safety factor of 2.2, assume the proportional limit for steel is 200 Mpa and E=208 Gpaarrow_forward
- Question 2 of 5 Design a circular column by specifying the diameter and length, of a steel column (E = 30 x 10° psi) that will carry a 50 kip load with a safety factor of 3. The design requirements are that it is in stable equilibrium and that bending will not be the failure mode. Ássume the ends are pinned at both ends. Answer using this format: A. GIVEN B. FORMULA C. SOLUTION with unit analysis D. FINAL ANSWERarrow_forwardRequired information A steel pipe having the cross section shown is used as a column. Use oy= 250 MPa, t = 6.3 mm, FOS = 1.67, and E= 200 GPa. 125 mm Using the AISC allowable stress design formulas, determine the allowable centric load if the effective length of the column is 6 m. The allowable centric load is 227.51 kN.arrow_forwardCalculate the critical load of a steel circular column for pinned-pinned boundary conditions using Johnson formula. The length of column is 300 mm, diameter is 60 mm and slenderness ratio is 40. The modulus of elasticity of steel is 207 GPa and yield strength is 300 MPa. Use safety factor 2.5. Select one: O a. 756.6 kN b. 715.3 kN c. 798.4 kNarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License