Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 14, Problem 31RQ
To determine
Whether the statement "If the differential of a motor control is set too small the motor may short cycle" is true or false.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A single-acting actuator could be used as a component for bus opening or closing as per the experiment
Select one:
True
False
In a DC machine, armature shaft is generally supported at the both ends by
Brushes
Bearings
Yoke
Commutator
5 position and 2-way type of ports DCV could be used in the double acting actuator circuit.
Select one:
True
False
Chapter 14 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 14 - Why is a low-voltage thermostat normally more...Ch. 14 - The three kinds of switching mechanism used in...Ch. 14 - Prob. 3RQCh. 14 - What does a cold anticipator do?Ch. 14 - Define system overshoot when dealing with...Ch. 14 - Prob. 6RQCh. 14 - Prob. 7RQCh. 14 - Describe the method a service technician should...Ch. 14 - Explain how microelectromc or electrontc...Ch. 14 - Prob. 10RQ
Ch. 14 - What component steps down the voltage to the...Ch. 14 - Low voltage is desirable for residential control...Ch. 14 - What is the maximum amperage usually encountered...Ch. 14 - Prob. 14RQCh. 14 - Prob. 15RQCh. 14 - What two types of switches are normally found in...Ch. 14 - Prob. 17RQCh. 14 - Prob. 18RQCh. 14 - Why is a line-voltage thermostat mounted on an...Ch. 14 - What is the principle of operation for most...Ch. 14 - Describe a method for speedmg up the cooling of an...Ch. 14 - Describe two methods for cooling an overheated...Ch. 14 - How can an electronic thermometer be used in a...Ch. 14 - A temperature-sensing device used in measuring...Ch. 14 - How does a thermocouple change with a temperature...Ch. 14 - True or False: Pressures below atmospheric...Ch. 14 - Name one function of the low-pressure control.Ch. 14 - Which is true of a high-pressure control? A. It...Ch. 14 - Name two types of water pressure control.Ch. 14 - Why should a safety control not be adjusted if it...Ch. 14 - Prob. 31RQCh. 14 - True or False: A change in the differential...Ch. 14 - True or False: A change in the differential of a...Ch. 14 - Prob. 34RQCh. 14 - Explain what is meant by the range of a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Refer to the schematic diagram in Figure 318. Assume that the motor is not running. When the third speed push button is pressed, the motor starts in its lowest speed. After a delay of 3 seconds, the motor accelerates to second speed and 3 seconds later to third speed. After a period of about 1 minute, the fourth speed push button is pressed, but the motor does not accelerate to fourth speed. Which of the following could cause this problem? a. Control relay CR2 coil is open. b. S2 contactor coil is open. c. CR3 coil is shorted. d. S3 contactor coil is open.arrow_forwardchoose true or false :1. The chain drive transmits more power as compared to belt drive.arrow_forwardDefine motorarrow_forward
- The variable which is to be controlled is known asarrow_forwardAn open winding in an electric motor means that A. the winding is making contact with the motor frame. B. one winding is making contact with another winding. C. a wire in one winding is broken. D. the centrifugal switch to the start winding is open.arrow_forwardIf an actuator fails to move, name five possible causes.If an actuator has slow or erratic motion, name five possible causes.arrow_forward
- True or False: Three-phase motors have low starting torque.arrow_forwardThis is for my mechatronics class in regards to PLC and ladder diagrams It is common practice to include a NC contact after the coil to prevent overloading and overheating of a device such as a motor. True or Falsearrow_forwardAdding resistance to the rotor circuit of :induction motor will Reduced the starting current and increase the starting O .torque Increase the starting current and increase the starting O .torque Increase the power transferred from stator to rotor and O .decrease the starting torquearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning