Concept explainers
A small 250-g collar C can slide on a semicircular rod which is made to rotate about the vertical AB at a constant rate of 7.5 rad/s. Knowing that the coefficients of friction are μs = 0.25 and μk = 0.20, indicate whether the collar will slide on the rod if it is released in the position corresponding to (a) θ = 75°, (b) θ = 40°. Also, determine the magnitude and direction of the friction force exerted on the collar immediately after release.
Fig. P12.64 and P12.65
(a)
Indicate whether the collar will slide on the rod if it is released in the position corresponding to angle
Find the magnitude and direction of the friction force exerted on the collar immediately after release.
Answer to Problem 12.65P
The collar does not slide on the rod if it is released in the position corresponding to angle
The magnitude and direction of the friction force exerted on the collar immediately after release is 0.611 N.
Explanation of Solution
Given information:
The mass of collar (m) is 250 g.
The speed of rotation of semi-circular rod
The radius (r) of semicircular rod is 500 mm.
The coefficient of static friction
The coefficient of kinetic friction
Calculation:
The collar will not slide. Therefore the collar moves at constant speed.
Find the equation of radius of circle for constant rotation.
Find the equation of speed of semicircular rod for constant rotation:
Find the equation of normal acceleration
Substitute
Substitute
Sketch the free body diagram and kinetic diagram of the collar C as shown in Figure (1).
Refer Figure (1):
Find the normal force (N) on the collar.
Apply Newton’s law of equation along x-axis.
Substitute
Substitute 250 g for m,
Find the frictional force (F) using Newton’s law of equation:
Apply Newton’s law of equation along y-axis.
Substitute
Substitute 250 g for m,
Find the frictional force using general equation:
Substitute 0.25 for
The frictional force
Thus, the magnitude and direction of the friction force exerted on the collar immediately after release is 0.611 N.
(b)
Indicate whether the collar will slide on the rod if it is released in the position corresponding to angle
Find the magnitude and direction of the friction force exerted on the collar immediately after release.
Answer to Problem 12.65P
The collar does not slide on the rod if it is released in the position corresponding to angle
The magnitude and direction of the friction force exerted on the collar immediately after release is 0.957 N.
Explanation of Solution
Calculation:
Find the normal force (N) on the collar using Equation (1):
Substitute 250 g for m,
Find the frictional force (F) using Equation (2):
Substitute 250 g for m,
Find the frictional force using general equation:
Substitute 0.25 for
The frictional force
Sketch the free body diagram and kinetic diagram of the collar C which is sliding as shown in Figure (2).
Refer Figure 2:
Find the normal force (N) on the collar.
Apply Newton’s law of equation along x-axis.
Substitute
Substitute 250 g for m,
Find the magnitude and direction of the friction force
Substitute 0.20 for
Thus, the magnitude and direction of the friction force exerted on the collar immediately after release is 0.957 N.
Want to see more full solutions like this?
Chapter 12 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Engineering Mechanics: Statics & Dynamics (14th Edition)
Fundamentals of Aerodynamics
Mechanics of Materials (10th Edition)
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
Vector Mechanics for Engineers: Statics, 11th Edition
- Two 2.6-lb collars A and B can slide without friction on a frame, consisting of the horizontal rod OE and the vertical rod CD, which is free to rotate about CD . The two collars are connected by a cord running over a pulley that is attached to the frame at O and a stop prevents collar B from moving. The frame is rotating at the rate 0 =12 rad/s and r= 0.6 ft when the stop is removed allowing collar A to move out along rod OE . Neglecting friction and the mass of the frame, determine, for the position r= 1.2 ft, (a) the transverse component of the velocity of collar A, (b) the tension in the cord and the acceleration of collar A relative to the rod OE.arrow_forward3. A block of mass m = 2.00 kg rests on the left edge of a block of mass M= 8.00 kg. The coefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00 kg block rests is frictionless. A constant horizontal force of magnitude F= 10.0N is applied to the 2.00-kg block, setting it in motion as shown in Figure. The distance L that the leading edge of the smaller block travels on the larger block is 3.00 m. F - m M M (a) Draw a separate free-body diagram for each block. (b) In what time interval will the smaller block make it to the right side of the 8.00-kg block? as (Note: Both blocks are set into motion when the force is applied.) (c) How far does the 8.00-kg block move in the process?arrow_forward3. A small block B fits inside a lot cut in arm OA which rotates in a vertical plane at a constant rate. The block remains in contact with the end of the slot closest to A and its speed is 1.4 m/s for 0< 0 <150°. Knowing that the block begins to slide when 0 = 150°, determine the coefficient of static friction between the block and the slot. V = 0.3 m Aarrow_forward
- 3. A block of mass m = 2.00 kg rests on the left edge of a block of mass M = 8.00 kg. The coefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00 kg block rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the 2.00-kg block, setting it in motion as shown in Figure. The distance L that the leading edge of the smaller block travels on the larger block is 3.00 m. m (a) Draw a separate free-body diagram for each block. (b) In what time interval will the smaller block make it to the right side of the 8.00-kg block? as (Note: Both blocks are set into motion when the force is applied.) (c) How far does the 8.00-kg block move in the process?arrow_forwardA system of blocks is pulled by a force P. The string connecting blocks A and B passes over a pulley whose coefficient of friction between string and pulley is 0.25. The coefficient of friction between surface and blocks is 0.20. Block A weighs 200N and block B weighs 30ON. Determine, a. the minimum value of P for impending motion to the right. b. the tension connecting block B. B= 30° В A 30°arrow_forwardA solid cylinder A rolls without slipping is connected to a block B by a cord passing over a frictionless pulley of negligible weight. The cord is fastened to an axis passing through the center of the cylinder which has a radius of 1ft and weight of 161lbs while block B weighs 200lbs. Determine the acceleration of B, the tension in the cord and friction force acting on A. W=200 lb B f0.2 W=161 lb 30° 45% Ans. GB= 2.38 ft per sec²; T = 98.3 lb; F = 5.95 lbarrow_forward
- 1. A small object of mass m is located on the surface of the disk with radius R if the magnitude of the coefficient of static friction between the object and the disc is u and the disc rotates with a certain angular speed so that the object of mass m slides from the disc which is at a height h. Prove that the horizontal distance traveled by the object is x = JuR2h 2. A child of mass 80 kg sits on a spinning disc and begins to slide if the coefficient of friction is 0.5 and the angular velocity of the rotating disc is 10rad/s. calculate the maximum radius R provided that the child can still sit and remain on the spinning disc? Compare your answer with the manual solution and use Matlab A beautiful jumper with mass m jumps from a height of 10 m (a Calculate the initial velocity V at the time of the diver's collision with the water and the estimated time from the time of the dive to the collision. Assume that the buoyant force of the water is able to balance the magnitude of the…arrow_forwardProblem 3.115 I A force Fo of 400 lb is applied to block B. Letting the weights of A and B be 55 and 73 lb, respectively, and letting the static and kinetic friction coefficients between blocks A and B be µi = 0.25, and the static and kinetic friction coefficients between block B and the ground be µ2 = 0.45, determine the accelerations of both blocks. Fo Barrow_forwardA small 250-g collar C can slide on a semicircular rod which is made to rotate about the vertical AB at a constant rate of 7.5 rad/s. Knowing that the coefficients of friction are μs = 0.25 and μk = 0.20, indicate whether the collar will slide on the rod if it is released in the position corresponding to (a) 0= 75°, (b) 0 = 40°. Also, determine the magnitude and direction of the friction force exerted on the collar immediately after release.arrow_forward
- To unload a bound stack of plywood from a truck, the driver first tilts the bed of the truck and then accelerates from rest. Knowing that the coefficients of friction between the bottom sheet of plywood and the bed are μs= 0.40 and μk= 0.30, determine (a) the smallest acceleration of the truck which will cause the stack of plywood to slide, (b) the acceleration of the truck which causes corner A of the stack to reach the end of the bed in 0.9 s.arrow_forwardKnowing that the coefficient of static friction between the tires and the road is 0.8 for the automobile (m=1130 kg) shown, determine ▼0,5 m 1.5 m 1 m normal reaction at front wheels (N), the car is assumed front wheel drive. normal reaction at rear wheels (N), the car is assumed front wheel drive. maximum acceleration (m/s²), the car is assumed front wheel drive. normal reaction at front wheel (N), the car is assumed rear wheel drive. normal reaction at rear wheel (N), the car is assumed rear wheel drive. maximum acceleration (m/s²), the car is assumed rear wheel drive.arrow_forwardQ2) A loaded Porter governor has four links each 200 mm long and are hinged at a distance of 40 mm from the axis of rotation. The mass of each ball is 2 kg and mass of the sleeve is 20 kg. The governor sleeve begins to rise at 300 r.p.m. when the links are at an angle of 35° to the vertical. Assuming the friction force to be constant, determine the minimum and maximum speed of rotation when the inclination of the arms to the vertical is 40°.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY