Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 25CQ
To determine
The reason for longitudinal strength of wood.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In general, wood is dried to _____ percent moisture for typical structural application rather than using it in green condition.
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each
Steel
Copper
Area, A
900 mm2
1,200 mm2
Modulus of elasticity, E
200 GPa
120 GPa
ents
Allowable compressive stress
140 MPa
70 MPa
ces
ents
Which of the following most nearly gives the load, in percent, carried by the copper?
ssors
Select the correct response
ication
44.44%
Niki
55.56%
Blogs
66.67%
33.33%
Courses
The mechanical properties of wood are in the axial direction (along the fibers) and the transversal direction (perpendicular to the fibers). Explain briefly how it changes.
Chapter 12 Solutions
Materials Science And Engineering Properties
Ch. 12 - Prob. 1CQCh. 12 - Prob. 2CQCh. 12 - Prob. 3CQCh. 12 - Prob. 4CQCh. 12 - Prob. 5CQCh. 12 - Prob. 6CQCh. 12 - Prob. 7CQCh. 12 - Prob. 8CQCh. 12 - Composite _________ is produced by laying fibers...Ch. 12 - Prob. 10CQ
Ch. 12 - Prob. 11CQCh. 12 - Prob. 12CQCh. 12 - Prob. 13CQCh. 12 - Prob. 14CQCh. 12 - Prob. 15CQCh. 12 - Prob. 16CQCh. 12 - Prob. 17CQCh. 12 - Prob. 18CQCh. 12 - Prob. 19CQCh. 12 - Prob. 20CQCh. 12 - Prob. 21CQCh. 12 - Prob. 22CQCh. 12 - Prob. 23CQCh. 12 - Prob. 24CQCh. 12 - Prob. 25CQCh. 12 - Prob. 26CQCh. 12 - Prob. 27CQCh. 12 - Prob. 28CQCh. 12 - Prob. 1ETSQCh. 12 - Prob. 2ETSQCh. 12 - Prob. 3ETSQCh. 12 - Prob. 4ETSQCh. 12 - Prob. 5ETSQCh. 12 - Prob. 6ETSQCh. 12 - Prob. 7ETSQCh. 12 - Prob. 8ETSQCh. 12 - Prob. 9ETSQCh. 12 - Prob. 10ETSQCh. 12 - In Example Problem 12.1, a uniaxial composite...Ch. 12 - Prob. 12.2PCh. 12 - Prob. 12.3PCh. 12 - Prob. 12.4PCh. 12 - Prob. 12.5PCh. 12 - Prob. 12.6PCh. 12 - Estimate the transverse tensile strength of the...Ch. 12 - Prob. 12.8PCh. 12 - Prob. 12.9PCh. 12 - Prob. 12.10PCh. 12 - Prob. 12.11PCh. 12 - Prob. 12.12PCh. 12 - Prob. 12.13PCh. 12 - Prob. 12.14PCh. 12 - Prob. 12.15PCh. 12 - Prob. 12.16PCh. 12 - Prob. 12.17P
Knowledge Booster
Similar questions
- Composite _________ is produced by laying fibers in random directions in a plane.arrow_forward4. For the composite block shown, determine (a) the value of h if the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (b) the total load if the stress in the brass is 80 Mpa. P Rigid end plate Aluminum Plates (E=70 GPa) Brass Core (E=105 GPa) 40 mm I h 60 mm 300 mmarrow_forwardThe following are functions of a matrix, EXCEPT: Subjects the fibers, which carry most of the load, to stresses Reduces the propagation of cracks in the composíte O Subjects the fibers from physical damage and the environmentarrow_forward
- A solid rod of bronze 20 mm in diameter is surrounded by a fitting steel cylinder of external diameter 28 mm. If the permissible bending stress in bronze and steel are 100 and 150 N/mm², find the moment of resistance of the composite section. The Young's modulus for steel may be taken as 1.75 times that of bronze.arrow_forward7 Has the same composition at any point? a. Isotropic b. Composite c. Prismatic d. Homogeneous 8. The composite material exhibits elastic properties in one direction different from that in the perpendicular direction. Orthotropic b. Anisotropic Isotropic d. Aeolotropic а. с. Materials having the same properties in all directions. a. Isotropic b. Anisotropic c. Aeolotropic d. Orthotropic 10 The term for the value above which the stress is no longer proportional to the strain. a. Proportional limit b. Plastic Range Rupture Stress d. Elastic Range с.arrow_forwardBasalt fiber bars in concrete Max tensile of basalt fibers is 1500 Mpa and resin is 6 Mpa rate of fibers in logway of the bar is 70% so how much is max tensile strength? А) 6 Мра В) 1500 Мра С) 1050 Мра d) 1051,8 Мраarrow_forward
- Which of the following is main advantage of using chopped fiber reinforcements ? Easier manufacturing Better control of directionality of fibers Avoid voids in the matrix Greater ratio of stress transferred to matrixarrow_forwardWhen looking up data for composite materials, it is important to: a.)Make sure the volume fraction of the fibres is specified b.)The orientation of each fibre layer is specified c.)The type of resin/matric is specified d.)All of the abovearrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning