Chemistry & Chemical Reactivity
10th Edition
ISBN: 9781337399074
Author: John C. Kotz, Paul M. Treichel, John Townsend, David Treichel
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 1, Problem 6PS
Interpretation Introduction
Interpretation:
The principles of green chemistry that matches for new process compared to older process has to be given.
Concept introduction:
Green chemistry:
The utilization of a set of principles that reduces or eliminates the use or generation of hazardous substances in the design, manufacture and the application of chemical products.
The new procedure applies all of these principles either to a greater or lesser extent.
- It is better to prevent waste than to treat or clean up waste after it is formed.
- Synthetic methods should be designed to maximize the incorporation of all materials used in the final product.
- Synthetic method should be designed to use and generate substances that possess little or no toxicity to human health or the environment.
- Chemical products should be designed to function effectively while still reducing toxicity.
- Synthetic methods should be conducted at ambient temperature and pressure.
- Raw materials should be renewable whenever technically and economically practical.
- Chemical products should be designed so that at the end of their function, they do not persist in the environmental or break down into dangerous products.
- Substances used in a chemical process should be chosen to minimize the potential for chemical accidents, including releases, explosions, and fires.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Concrete is prepared by roasting the mineral calcium carbonate, CaCO3, to drive off CO2 and produce calcium oxide, CaO. The chemical equation for this reaction is:
CaCO3 ==> CaO + CO2
The Grand Coulee Dam on the Columbia River in Washington State was built using a volume of concrete of approximately 1.0 x 107 m3. If concrete has a density of 2.4 x 103 kg/m3, and assuming concrete is 100% by volume CaO, how much CO2 was released producing the concrete used to build the dam?
Consider the following reactions:CoO (s) + CO (g) D CO2 (g) + Co (s) Kc(1) = 490.2 CoO (s) + 2 H2 (g) D 2 Co (s) + 2 H2O (g) Kc(2) = 4.5 x 103a. Write the overall equation for the reaction of hydrogen gas and carbon dioxide gas to produce carbon monoxide gas and steam.
ebixoiC
4 During the production of ammonia, hydrogen is produced from the steam
reforming of methane. In the reformer methane gas is reacted with excess water
and the resulting mixture is found to contain 12 kg of hydrogen and 15 kg water.
Assuming all the methane is reacted calculate the amount of water used.
Chapter 1 Solutions
Chemistry & Chemical Reactivity
Ch. 1.5 - Prob. 1.1CYUCh. 1.6 - Prob. 1.2CYUCh. 1.6 - Identify whether each of the following properties...Ch. 1.7 - Identify whether each of the following is a...Ch. 1.8 - Much has been written about CO2.What is its name?Ch. 1.8 - Prob. 1.2ACPCh. 1.8 - Prob. 1.3ACPCh. 1.8 - The spines of the sea urchin, corals, and...Ch. 1 - In the following scenario, identify which of the...Ch. 1 - State whether the following is a hypothesis,...
Ch. 1 - What is meant by the phrase sustainable...Ch. 1 - Prob. 4PSCh. 1 - Prob. 5PSCh. 1 - Prob. 6PSCh. 1 - Give the name of each of the following elements:...Ch. 1 - Give the name of each of the following elements:...Ch. 1 - Give the symbol for each of the following...Ch. 1 - Give the symbol for each of the following...Ch. 1 - In each of the following pairs, decide which is an...Ch. 1 - In each of the following pairs, decide which is an...Ch. 1 - An 18 g sample of water is decomposed into 2 g of...Ch. 1 - A sample of the compound magnesium oxide is...Ch. 1 - In each case, decide if the underlined property is...Ch. 1 - In each case, decide if the change is a chemical...Ch. 1 - Which part of the description of a compound or...Ch. 1 - Which part of the description of a compound or...Ch. 1 - The flashlight in the photo does not use...Ch. 1 - A solar panel is pictured in the photo. When light...Ch. 1 - Determine which of the following represent...Ch. 1 - Prob. 22PSCh. 1 - A hot metal block is plunged into water in a...Ch. 1 - A book is held at a height above the floor. It has...Ch. 1 - Prob. 25GQCh. 1 - Iron pyrite (fool's gold, page 11) has a shiny...Ch. 1 - Which observations below describe chemical...Ch. 1 - Which observations below describe chemical...Ch. 1 - The mineral fluorite contains the elements calcium...Ch. 1 - Azurite, a blue, crystalline mineral, is composed...Ch. 1 - You have a solution of NaCI dissolved in water....Ch. 1 - Small chips of iron are mixed with sand (see...Ch. 1 - Identify the following as either physical changes...Ch. 1 - Identify the following as either physical changes...Ch. 1 - In Figure 1.2 you see a piece of salt and a...Ch. 1 - In Figure 1.5 you see macroscopic and particulate...Ch. 1 - Prob. 37GQCh. 1 - The following photo shows copper balls, immersed...Ch. 1 - Categorize each of the following as an element, a...Ch. 1 - Categorize each of the following as an element, a...Ch. 1 - Make a drawing, based on the kinetic-molecular...Ch. 1 - Make a drawing, based on the kinetic-molecular...Ch. 1 - Hexane (C6H14, density = 0.766 g/cm3),...Ch. 1 - You have a sample of a white crystalline substance...Ch. 1 - You can figure out whether a solid floats or sinks...Ch. 1 - You are given a sample of a silvery metal. What...Ch. 1 - Milk in a glass bottle was placed in the freezing...Ch. 1 - Describe an experimental method that can be used...Ch. 1 - Diabetes can alter the density of urine, so urine...Ch. 1 - Prob. 50GQCh. 1 - The following photo shows the element potassium...Ch. 1 - Prob. 52GQCh. 1 - Four balloons are each filled with a different...Ch. 1 - Prob. 54GQCh. 1 - The photo below shows elemental iodine dissolving...Ch. 1 - A few years ago a young chemist in Vienna,...Ch. 1 - The distance between two carbon atoms in diamond...Ch. 1 - A student checked the accuracy of two standard...Ch. 1 - Prob. 3RCYUCh. 1 - The density of gold is 19,320 kg/m3. What is this...Ch. 1 - A particular paint has a density of 0.914 g/cm3....Ch. 1 - What is the fuel density in units of kg/L?Ch. 1 - What mass and what volume of fuel should have been...Ch. 1 - Confirm that a person swimming at the world record...Ch. 1 - At this world record rate, how long would it take...Ch. 1 - Prob. 2.3RACh. 1 - Many laboratories use 25C as a standard...Ch. 1 - The temperature on the surface of the Sun is 5.5 ...Ch. 1 - Prob. 3RPSCh. 1 - Make the following temperature conversions:Ch. 1 - A marathon distance race covers distance of 42.195...Ch. 1 - The average lead pencil, new and unused, is 19 cm...Ch. 1 - A standard U.S. postage stamp is 2.5 cm long and...Ch. 1 - A compact disc has a diameter of 11.8 cm. What is...Ch. 1 - A typical laboratory beaker has a volume of 250....Ch. 1 - Some soft drinks are sold in bottles with a volume...Ch. 1 - A book has a mass of 2.52 kg. What is this mass in...Ch. 1 - A new U.S. dime has a mass of 2.265 g. What is its...Ch. 1 - Ethylene glycol, C2H6O2, is an ingredient of...Ch. 1 - A piece of silver metal has a mass of 2.365 g. If...Ch. 1 - Prob. 15RPSCh. 1 - Which occupies a larger volume, 600 g of water...Ch. 1 - You are on a diet that calls for eating no more...Ch. 1 - A 2-in. piece of chocolate cake with frosting...Ch. 1 - Prob. 19RPSCh. 1 - Prob. 20RPSCh. 1 - You and your lab partner are asked to determine...Ch. 1 - The accepted value of the melting point of...Ch. 1 - Prob. 23RPSCh. 1 - Prob. 24RPSCh. 1 - Prob. 25RPSCh. 1 - Prob. 26RPSCh. 1 - To determine the average mass of a popcorn kernel,...Ch. 1 - Use the following graph to answer the following...Ch. 1 - Use the graph below to answer the following...Ch. 1 - Solve the following equation for the unknown...Ch. 1 - Solve the following equation for the unknown...Ch. 1 - Solve the following equation for the unknown...Ch. 1 - Prob. 34RPSCh. 1 - Molecular distances are usually given in...Ch. 1 - The separation between carbon atoms in diamond is...Ch. 1 - A red blood cell has a diameter of 7.5 m...Ch. 1 - The platinum-containing cancer drug cisplatin...Ch. 1 - Prob. 39RGQCh. 1 - You need a cube of aluminum with a mass of 7.6 g....Ch. 1 - You have a 250.0-mL graduated cylinder containing...Ch. 1 - Prob. 42RGQCh. 1 - The smallest repeating unit of a crystal of common...Ch. 1 - Diamond has a density of 3.513 g/cm3. The mass of...Ch. 1 - Prob. 45RGQCh. 1 - The density of pure water at various temperatures...Ch. 1 - Prob. 47RGQCh. 1 - The aluminum in a package containing 75 ft2 of...Ch. 1 - Fluoridation of city water supplies has been...Ch. 1 - About two centuries ago, Benjamin Franklin showed...Ch. 1 - Prob. 51RGQCh. 1 - A 26-meter-tall statue of Buddha in Tibet is...Ch. 1 - At 25 C, the density of water is 0.997 g/cm3,...Ch. 1 - Suppose your bedroom is 18 ft long and 15 ft wide,...Ch. 1 - A spherical steel ball has a mass of 3.475 g and a...Ch. 1 - You are asked to identify an unknown liquid that...Ch. 1 - You have an irregularly shaped piece of an unknown...Ch. 1 - There are five hydrocarbon compounds (compounds of...Ch. 1 - Suppose you have a cylindrical glass tube with a...Ch. 1 - Copper: Copper has a density of 8.96 g/cm3 An...Ch. 1 - Copper: (a) Suppose you have a cube of copper...Ch. 1 - You set out to determine the density of lead in...Ch. 1 - A sample of unknown metal is placed in a graduated...Ch. 1 - Iron pyrite is often called fool's gold because it...Ch. 1 - You can analyze for a copper compound in water...Ch. 1 - Prob. 67RIL
Knowledge Booster
Similar questions
- A power plant is driven by the combustion of a complex fossil fuel having the formula C11H7S. Assume the air supply is composed of only N2 and O2 with a molar ratio of 3.76:1.00, and the N2 remains unreacted. In addition to the water produced, the fuels C is completely combusted to CO2 and its sulfur content is converted to SO2. In order to evaluate gases emitted at the exhaust stacks for environmental regulation purposes, the nitrogen supplied with the air must also be included in the balanced reactions. a Including the N2 supplied m the air, write a balanced combustion equation for the complex fuel assuming 100% stoichiometric combustion (i.e., when there is no excess oxygen in the products and the only C-containing product is CO2). Except in the case of N2, use only integer coefficients. b Including N2 supplied in the air, write a balanced combustion equation for the complex fuel assuming 120% stoichiometric combustion (i.e., when excess oxygen is present in the products and the only C-containing product is CO2). Except in the case of use only integer coefficients c Calculate the minimum mass (in kg) of air required to completely combust 1700 kg of C11H7S. d Calculate the air/fuel mass ratio, assuming 100% stoichiometric combustion. e Calculate the air/fuel mass ratio, assuming 120% stoichiometric combustion.arrow_forward62 Ammonium dinitramide (ADN), NH4N(NO2)2, was considered as a possible replacement for aluminium chloride as the oxidizer in the solid fuel booster rockets used to launch the space shuttle. When detonated by a spark, AND rapidly decomposes to produce a gaseous mixture of N2,O2, and H2O. (This is not a combustion reaction. The ADN is the only reactant.) The reaction releases a lot of heat, so the gases are initially formed at high temperature and pressure. The thrust of the rocket results mainly from the expansion of this gas mixture. Suppose a 2.3-kg sample of ADN is denoted and decomposes completely to give N2,O2, and H2O. If the resulting gas mixture expands until it reaches a temperature of 100°C and a pressure of 1.00 atm, what volume will it occupy? Is your answer consistent with the proposed use of ADN as a rocket fuel?arrow_forwardAssume that the radius of Earth is 6400 km, the crust is 50. km thick, the density of the crust is 3.5 g/cm3, and 25.7% of the crust is silicon by mass. Calculate the total mass of silicon in the crust of Earth.arrow_forward
- Suppose that you are closing a cabin in the north woods for the winter and you do not want the water in the toilet tank to freeze. You know that the temperature might get as low as 30. C, and you want to protect about 4.0 L water in the toilet tank from freezing. Calculate the volume of ethylene glycol (density = 1.113 g/mL; molar mass = 62.1 g/mol) you should add to the 4.0 L water.arrow_forward1. A candle is placed on one pan of a balance, and an equal weight is placed on the other pan. What would happen if you lit up the candle and waited for a while? Suppose the candle was placed in a large, sealed jar that allowed it to burn for several minutes before running out of oxygen. The candle and jar are balanced by an equal weight. In this situation, what would happen if you lit up the candle and waited?arrow_forwardThe human body burns glucose (C6H₁2O6) for energy according to this chemical reaction: C6H12O6 +60₂-6CO₂ + 6H₂O The products of the reaction are carbon dioxide (CO₂) and water (H₂O). Interestingly, all of the carbon dioxide and much of the water exits the body through the lungs: on every breath, the average person exhales 500. mL of air, which is typically enriched to 4% CO₂ and 5% water vapor by volume. In short, when a person loses weight by dieting, the weight that is lost actually departs his body as a gas, every time he exhales. Each kilogram of body fat lost requires exhaling about 2.9 kg of carbon dioxide. Calculate how many breaths it takes an average person to "exhale" 1.00 kg of fat. Round your answer to the nearest thousand. You'll need to know that the density of CO₂ is 2.0 kg/m³. 0 ☐ ☐x10 Xarrow_forward
- One method used in the production of H2 gas is to put the coal into an incomplete combustion reaction with air and water vapor in the combustion chamber (water gas production). A simplified reaction can be written as:2C + 1 H2O + a (O2+3.76N2) = 1C0 + 1CO2 + 1H2 + 3.76·a·N2 Here, 02+3.76N2 represents the amount of air and is multiplied by the coefficient "a".a) The value of the coefficient "a" for this reaction b) The amount of air to be used for 1 kg of pure carbon (C) (total amount of 02 and N2) (kg-air/kg-carbon) Hint: Consider how many kilograms 1 kmol "C" weighs.arrow_forward10 Ethylene (CH, CH,) is the starting point for a wide array of industrial chemical syntheses. For example, worldwide about 8.0 x 10" kg of polyethylene are made from ethylene each year, for use in everything from household plumbing to artificial joints. Natural sources of ethylene are entirely inadequate to meet world demand, so ethane (CH, CH,) from natural gas is "cracked" in refineries at high temperature in a kinetically complex reaction that produces ethylene gas and hydrogen gas. Suppose an engineer studying ethane cracking fills a 60.0 L reaction tank with 29.0 atm of ethane gas and raises the temperature to 500. °C. He believes K =0.30 at this temperature. Calculate the percent by mass of ethylene the engineer expects to find in the equilibrium gas mixture. Round your answer to 2 significant digits. Note for advanced students: the engineer may be mistaken about the correct value of K, and the mass percent of ethylene you calculate may not be what he actually observes. % x10arrow_forwardAs part of the aspirin synthesis lab the orgo students also had to perform the following calculation to demonstrate their knowledge. Are you able to help them work this out? Saponification is a process in which soap is produced from the chemical reaction between animal fat (triglycerides) and a strong base such as KOH. An example of such balanced chemical reaction is shown here: C51H98O6 + 3KOH → C3H5(OH)3 + 3C16H31O2K (Triglyceride) (Soap) if during the saponification reaction 231.5 g of C51H98O6 is mixed with 231.5 g of KOH and 160 g of soap is produced. Calculate the theoretical yield of soap C16H31O2K and indicate who is the limiting reactant. (Provide your answer to 2 decimal places) Calculate the percent yield for this reaction (Provide your answer to 1 decimal place) *Show ALL steps and mathematical equations involved in your calculations to help the orgo students. Remember to label all…arrow_forward
- One way the U.S. Environmental Protection Agency (EPA) tests for chloride contaminants in water is by titrating a sample of silver nitrate solution. Any chloride anions in solution will combine with the silver cations to produce bright white silver chloride precipitate. Suppose an EPA chemist tests a 200. mL sample of groundwater known to be contaminated with iron(III) chloride, which would react with silver nitrate solution like this: FeCl3(aq) + 3 AgNO3(aq) 3 AgCl(s) + Fe(NO3),(a9) The chemist adds 56.0 mM silver nitrate solution to the sample until silver chloride stops forming. She then washes, dries, and weighs the precipitate. She finds she has collected 2.8 mg of silver chloride. Calculate the concentration of iron(III) chloride contaminant in the original groundwater sample. Be sure your answer has the correct number of significant digits. mg L Submit Assignment Continue Accessibility Privacy O 2020 McGraw-Hill Education. All Rights Reserved. Terms of Use 888 %23 5 6 2 3 E R. G…arrow_forwardExpress your answer as a chemical equation. Identify all of the phases in your answer. 1. Solid lead(II)(II) sulfide reacts with aqueous hydrochloric acid to form solid lead(II)(II) chloride and dihydrogen sulfide gas. 2. Gaseous carbon monoxide reacts with hydrogen gas to form gaseous methane (CH4)(CH4) and liquid water. 3. Solid iron(III)(III) oxide reacts with hydrogen gas to form solid iron and liquid water. 4. Gaseous ammonia (NH3)(NH3) reacts with gaseous oxygen to form gaseous nitrogen monoxide and gaseous water.arrow_forwardThe emission of NO2 by fossil fuel combustion can be prevented by injecting gaseous urea into the combustion mixture. The urea reduces NO (which oxidizes in air to form NO2) according to the reaction:2 CO(NH2)2( g) + 4 NO( g) + O2( g)------------->4 N2( g) + 2 CO2( g) + 4 H2O( g)Suppose that the exhaust stream of an automobile has a flow rate of 2.55 L/s at 655 K and contains a partial pressure of NO of 12.4 torr. What total mass of urea is necessary to react completely with the NO formed during 8.0 hours of driving?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Chemistry & Chemical ReactivityChemistryISBN:9781337399074Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781133949640Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
- Chemistry: An Atoms First ApproachChemistryISBN:9781305079243Author:Steven S. Zumdahl, Susan A. ZumdahlPublisher:Cengage LearningChemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage Learning
Chemistry & Chemical Reactivity
Chemistry
ISBN:9781337399074
Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel
Publisher:Cengage Learning
Chemistry & Chemical Reactivity
Chemistry
ISBN:9781133949640
Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry: An Atoms First Approach
Chemistry
ISBN:9781305079243
Author:Steven S. Zumdahl, Susan A. Zumdahl
Publisher:Cengage Learning
Chemistry: The Molecular Science
Chemistry
ISBN:9781285199047
Author:John W. Moore, Conrad L. Stanitski
Publisher:Cengage Learning