Logic Gates: * 7404LS (NOT) * 7408LS (AND) * 7432LS (OR) * 7400LS (NAND) * 7402LS (NOR) * 7486LS (EX-OR) Or you can use 74HCxx versions. Task 1: 2-to-1 LINE MULTIPLEXER DESIGN A) Write the truth table of 2-to-1 line multiplexer. B) Draw the circuit diagram by using only NAND & NOT GATES. C) Simulate the circuit that you found in part B.

Logic Gates: * 7404LS (NOT) * 7408LS (AND) * 7432LS (OR) * 7400LS (NAND) * 7402LS (NOR) * 7486LS (EX-OR) Or you can use 74HCxx versions. Task 1: 2-to-1 LINE MULTIPLEXER DESIGN A) Write the truth table of 2-to-1 line multiplexer. B) Draw the circuit diagram by using only NAND & NOT GATES. C) Simulate the circuit that you found in part B.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)
The logic circuit: (From minimum SOP) Number of gates used in the circuit: 2-Input AND gate.. 2-Input OR gate. NOT gate Number of idle gates in the chip: 2-Input AND gate 2-Input OR gate... NOT gute The logic circuit: (From minimum POS) gates gates gates gates gutes Number of gates used in the circuit: 2-Input AND gate 2-Input OR gate... NOT gate Number of idle gates in the chip: 2-Input AND gate... 2-Input OR gate, NOT gate, IC name: IC name: IC name: gates IC name: gates IC name: gates IC name: gates gates gates
Question 3:a) We can construct the full adder/Sub tractor with the help of AND-OR gate and also by using exclusive OR Gate. What is the between these two circuits?b) Construct the circuit of multiplexer which can multiply more than two bits.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
draw the curcuit diagram for 4 channel 4 bit multiplexer implemented using 4 channel 1 bit multiplexer. make sure that i need full circuit to save the final multiplexer in the library.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Implement the function, W using ONE 4-to-1 multiplexer and other logic gates. b) Implement the function, X using ONE 4-to-1 multiplexer and other logic gates. Implement the function, Y using TWO 4-to-1 multiplexer and other logic gates. d) Implement the function, Z using ONE 8-to-1 multiplexer and other logic gates. Table Q1 ВCD Braille A B D W Y 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A ololO
logic circuit diagram for fabinaaci counter that gives output in fabinaaci sequence.upto 2 digits please mentions the gates and ics used in circuit.
Q3) A - Convert the Excess-3 to binary number : ( 110001011100.10001010)ex-3 B- convert each Gray code to binary: 1-( 011010001001)G 2-(59)D
2) The output of a logic gate is 0 when all its inputs are logic 1. The logic is either (A) a NAND or an EX-OR (B) an OR or an EX-NOR (C) an AND or an EX-OR (D) an NOR or an EX-NOR
Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit