I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered.NOTE: Read the instructions, no where does it say any drawing is required. It is really frustrating when I wait all this time for an answer to a question and some tutor does even read the instructions and just declines it...its ridicilous. IT VIVCHPrint Reading for Industry228ClassDateNameReview Activity 11-2For each local note or callout given on the next page, use lettering to put the notes into words thatexample has been done for you. Also refer to Figure 11-5 as needed.can read. Anyou1. Two .500" diameter holes, .375" deep.2.3.4.5.6.7.8A9-10.nheart-Willcox Co, In

(8) Four 0.562” diameter of drill (through holes), each with 0.625” counter bore diameter with spot…

IT VIVCH Print Reading for Industry 228 Class Date Name Review Activity 11-2 For each local note or callout given on the next page, use lettering to put the notes into words that example has been done for you. Also refer to Figure 11-5 as needed. can read. An you 1. Two .500" diameter holes, .375" deep. 2. 3. 4. 5. 6. 7. 8A 9- 10. nheart-Willcox Co, In

IT VIVCH Print Reading for Industry 228 Class Date Name Review Activity 11-2 For each local note or callout given on the next page, use lettering to put the notes into words that example has been done for you. Also refer to Figure 11-5 as needed. can read. An you 1. Two .500" diameter holes, .375" deep. 2. 3. 4. 5. 6. 7. 8A 9- 10. nheart-Willcox Co, In

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.6: Cnc Milling: Programming

Problem 8RQ: Briefly describe the use of I and J for the arc center method of circular interpolation.

See similar textbooks

Similar questions

answerquickly
6. Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).
While constructing a building, an engineer need to fix two steel beams together using a bracket as shown in Figure 1. Using absolute coordinate system, construct a G-code program for drilling hole number 2 only. To remove the metal chips the hole should be done in two equal steps. During the drilling, coolant should be on after spindle starts and stop before spindle stops. The spindle speed set to 1750 RPM. Drilling bit in rack number 2 and it should be 2 mm over the work piece. Drilling feed rate is 25 mm/min. Explain each code used in the program in a column. 57.5- 12.5 Hole (4) Hole (3) 30 10 Hole (2) Hole (1) X0 YO ZO 10 15 All dimensions shown are in mm Figure 1
I need help answering problems 13, 14, and 15 pertaining to the print attatched below.
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
please type so that I can read your solution do not handwrite
7. Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).
answerDcorrectly.
Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45
Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different colour 20 10R 1OR 2 holes 10 Dia 10 116 Dia 40R YOR 18R Face-plate 20
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Page 6 of a Another name for "SIZE DESCRIPTION" is: A Dimensioning. B Orthographic projection. C Assembly drawing. D Pictorial drawing What is the length to width ratio of arrowheads? A 1:1 37 42 в 2:1 С 3:1 D 5:1 Leader lines should NOT be drawn: 38 "2X on a hole note means: 43 A At 45°. A Double the size of the hole. B At 30°. C At 60°. D Horizontally or Vertically. B Reduce the stated size by 1/2. C The scale of the hole is doubled. D There are two boles the same size. Extension lines are drawn: 39 Avoid dimensioning to: 44 A Extremely thick, A Hidden lines. B Thick. B Center lines, C Thin. D Extremely light. C Extension lines. D Holes. What is the standard length for arrowheads? CIRCLE SIZE is specified by: 45 40 A 031 (.5mm) B 063 (Imm) A Chord. B Circumference. C Diameter. C. 125 (3mm) D 250 (6mm) D Radius. Dimension lines should be: 41 46 The size of an ARC is typically specified by its: A Thick and dark. A Diameter, B Thick and light. B Circumference. C Chord. C Thin and dark.…