Draw front and right-side views of the following object with acompleted dimensions. Draw in scale 1:1 on A4 sheet.(Problem is taken from "Graphics for Engineers' by Earle)78What can we learm from the drawlng ?1. The dimension note M10x1.5 means that the hole is a threaded hole.R16O 16, 2 HolesThe letter 'M' means that the threads are made by following a metricthread system. The number "10" Is the major dlameter of the hole andthe number 1.5 is the pitch of a thread. However, for coarse threads, itis a common practice to omit specifying the pitches. For example, anote M10 means the pitches of the thread is 1.5 mm. In this book, thepitch is specified in order to facilitate drafting.2. Drawing symbol of a threaded hole is shown below.- Thin Ine (4H penchThe ends of this arcdoes not meet togetherbut approximately 90degs, apart.Object Ihe(2i pencil.major dlameterpich2M10x1 53. The circular projection surface at a threaded hole that is raisedfrom a cylinder is called "Boss'. Usually, the top surface of a bosis a finished surface to make a smooth seat for fastener. Thefollowing figure shows a side view of a boss with a drilled hole.Driledhole50Not to scale.046O 68NOTE : All fillets and rounds are 3 mmFRONT VIEWYOKEBossCylInderunless otherwise specified.ORTHOGRAPHIC WRITINGPAGE 4-21

Answered: Image /qna-images/answer/f6e19eba-69e3-4b5f-94f7-f3b2a0114771.jpg

Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers" by Earle) What can we learm from the drawlng ? 1. The dimension note M1Ox1.5 means that the hole is a threaded hole. The letter "M means that the threads are made by following a metric threed sustem The number 10 s the meior dlameter of the hole and

Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers" by Earle) What can we learm from the drawlng ? 1. The dimension note M1Ox1.5 means that the hole is a threaded hole. The letter "M means that the threads are made by following a metric threed sustem The number 10 s the meior dlameter of the hole and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Create the following drawing in autocad. Please show Layers and Dimensions.
AutoCAD Sketching The given sketch is a cross section view of housing. Sketch the 2D sketch of the below figure using AutoCAD. Note: color the hatching if there any and mention the dimensions and reference lines 58 8 holes 10 Dia 40 Dia 15R 16 20R 58 Dia 20R 6 holes 8la 40 40 Housing 22
Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on the drawing 2- Draw with the same measurements as shown 3 -Show graphics properties At least properties are required for the circle and arc R10 R20 40 35 55 -1- JSI 9.
Using the graphical method, find the sum of the vectors in each number. Draw your vectors on a separate sheet of paper. Scale 10 units: 1cm 1. A box was pushed with a force of 20 Newtons to the right and 40 Newtons to the left. What is the sum of these vectors?
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
Draw an orthographic drawing in a title block using 3d angle projection techniques for the isometric diagram in Figure 2, with X is taken as the front view. Also, create a section view taking A-B as the cutting plane. Show any detail where necessary and fully dimension your drawing. 60 60 35 75 中40 60 25 R23 Figure 2: Isometric drawing of an anchor bracket (unit is in mm) 09 15
The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure using AutoCAD. Note: Color the hatching if there any and mention the dimensions and reference lines 8holes 10 Dia 60 Dia 96 R 42 R 36 42R 16 80 Plate 85
Sketch the 2D figure using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 20 36 R 20R BR 36 BR 15 45 45 Upright | 2 holes 10 Dia 36K 158
[Chapter 2: Drawing in AutoCAD®] P2-8) May be attempted after completing the Object Snap Tutorial in section 2.20. Draw the following object in AutoCAD using object snap commands where necessary. Put your name on the drawing and then print it using a Window and the Scale to Fit option. Dimensions are in inches. 3.00 4.00 3.25 Perpendicular Tangent #3.00
Draw the following shapes using AutoCAD 2017 R15 5 30 R2 30 40
a diagonal of a polygon is a line segment that connects nonadjacent vertices of the polygon.in the following polygons, a triangle has 3 sides and 0 diagonal, a quadrilateral has 4 sides and 2 diagonals, a pentagon has 5 sides and 5 diagonals, a hexagon has 6 sides and 9 diagonals. predicts the number of diagonals in a 12-sided polygon.
Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 8R 6 holes 8 Dia 62 Dia 18 R 3 holes 20 Dia 110 Cover 40 Dia 100 R