İ need help very quickly to solve this questions pls 2L150mmz(+)L = 225mmL= 225mmx(+)y(+)140 NIf the 16 mm diameter solid ABC steel pipe is fixed at point A andexposed to a force of 140 N applied in the -z direction from the other endof the pipe, that is, point B, it will form at the H point;a) principal planes(p1,p2)b) principal stresses (qmax,qmin)c) view of the principal planed) planes of maximum shear stress(qs1,qs2)e) the maximum shear stress and (tmax) and the corresponding normalstress (q')f) Find the aspect of the maximum shear stress plane.note: the stress plane where the h point is located is parallel to the xyplane and the h point is on the top and outer surface of the steel pipe.also, point H is 150 mm away from point B.

Answered: Image /qna-images/answer/78c3303d-b5b4-4953-adbd-fb2ed4695ebe.jpg

Answered: ery quickly to solve this que

Engineering

Mechanical Engineering

ery quickly to solve this que

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Part A Fuc= 0.97 5m HA 2m KN Determine the magnitude of the projected component of the F-5 kN force acting along the axis BC of the pipe. Suppose that a 3.1 m and b=4.4 m (Figure 1) Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining B ? a 1m 1 of 1
Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress-30 MPa
The inner diameter of the AB compressed air tank is 160, the wall thickness is 1.Since the manometer pressure in the tank is 1,6 ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16 , d=38, e =32, g=160, h=1, k =1.6 , F=160)
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, P = 20 kN, P, = 16 kN, and P; = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a P: P H K
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
A thin-walled cylinder tank is subjected to a tensile stress of 100 Mpa. What is the longitudinal stress developed in the wall of the tank? (A) 50 MPa (C) 150 MPa (B) 100 MPa (D) 200 MPa
The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal and circumferential stress caused by an internal pressure of 125 psi (Ib/in²). 1. Drive the expressions for longitudinal and tangentional stresses? 2. Calculate the maximum longitudinal and circumferential stress caused by an internal pressure? Fw Fw Fp Fp XLV 1.5 ft |1= 1/8 in Fw Fw Fw Fw 0.75 ft LONGITUDINAL STRESS, ₁ TANGENTIAL STRESS , 2 ft 1.5ft ث إضافة ملف
The tank shown in the figure is fabricated from 10 mm steel plate. Determine themaximum longitudinal and circumferential stress caused by an internal pressure of 1.2MPa.
3: T = 10.11 kN-m
The problem I am solving shows a point B on the OD of the pipe that lies on the z-axis. When using the equation tau =(Mr)/J, I get 15.5 MPa, not 124 MPa
Q4 Direct stresses of 160N/mm2 tensile and 120 N/mm2 compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm2. What must be the magnitude of the shearing stresses on the two planes? What will be the maximum shearing stress at the point?
b2 h G B M. Q4) For the given system; a) Draw internal force diagrams and determine the most critical section. b) Show the stress distribution on this critical section and find the maximum normal stress. GIVEN: (1 = 50 cm, {2= 30 cm, M, = 5000 Nem, q. = 20 N/cm, bị = 4 cm, b2 = 2 cm, h = 4 cm, t= 1 cm