Design a trapezoidal S.A.F stilling basin (Full design: chute blocks, baffle blocks, endsill, and side walls) and draw a full details of a single chute block and baffle block usingthe given data (Note: use the attached chart):Flow discharge per unit width (q)= 24 m²/sec.Head loss throughout the basin (HL) 1.5 m.Ex-7.2 m.Basin width at the end sill (BE)- 20 m.Tail water depth-6 m.Slope of the glacis- 30°.Flaring (1:2) 1:6.

Approach to solving the question: Detailed explanation: Examples: Key references:

Answered: Design a trapezoidal S.A.F stilling…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the site development plan for a subdivision considering the storm drainage systembelow, consider the following storm event details:a. I = 2,481.44(t + d)^–0.6477b. d = 15 minsc. t = 10 mins (initial)Determine the following:1. Discharge Q in lps at Pipe 1 (L = 20 m)2. Discharge Q in lps at Pipe 2 (L = 20 m)3. Discharge Q in lps at Pipe 3 (L = 20 m)4. Discharge Q in lps at Pipe 4 (L = 20 m)5. Total time of discharge from the first inlet to the outfallNote: Use the Rational Method to compute Q.
Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A lined rectangular channel (n = 0.015) has a flow depth of 2m and a bed slope of 1 in 1600. Width of a channel is equal to the last digit of your registration number in meters. Retaining the rectangular shape and same total perimeter of a lining, DISCOVER the change in discharge for a most efficient x-section of a channel, if the bed slope, channel width and manning’s n remain same. b).DISCUSS the critical depth, normal depth and hydraulic depth of flow for subcritical and supercritical flow in open channel.
A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Determine the following: a.) Discharge flowing in the pipe, f = 0.012; b.) Discharge flowing in the pipe, n = 0.014; c.) Discharge flowing using C = 120 im iong PIune tnat Tuns on
For the pipe show, determine the depth of flow. LO: Q=- 50 cfs S = 0.01 E - 0.005' u = 2.34x10 slug/ft-s p= 1.94 slug/f 3'
A. Design a trapezoidal channel to carry a discharge of 10.5 m^3/s. The bottom slop of the channel is 0.0035. Also the flow depth is half of the channel bottom width. Take roughness coefficient as 0.025 and side slop as 1H to 4V. B. Based on the given information and your results in part A, compute the state of flow
1. Calculate the discharge through a 90 mm o sharped edge orifice. Assume Cd = 0.65.
Don't copy from Chegg.. I need all right solutions with clear calculations. Determine the normal flow depth, Froude Number at normal depth and the critical depth for the rectangular channel has a width of 6 m and convey a discharge of 24 m3/s with Manning’s n=0.012 and the streamwise slope is 1 in 200. Determine whether the normal flow is subcritical or supercritical
Compute the value of discharge through pipe having cross sectional area of pipe is 4 m2 and flow velocity is 2.1 m/s
Question 48 A circular pipe has a diameter of 1m, bed slope of 1 in 1000, and Manning's roughness coefficient equal to 0.01. It may be treated as an open channel flow when it is flowing just full, i.e., the water level just touches the crest. The discharge in this condition is denoted by Qfull- Similarly, the discharge when the pipe is flowing half-full i.e., with a flow depth of 0.5m, is denoted by Qhalf. The ratio Qfull/Qhalf İs:
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a %3D special fluid of SG=1.2, What is the direction of the flow? 1 550mmo 7.88m 2 2.95m Datum O point 1 to 2 O No flow point 2 to 1
1. Determine the discharge rate through three parallel corrugated metal pipe culverts shown in the sketch below (Use the outlet control). The 48-inch diameter culverts have a Manning, n value of 0.024. The culverts are 80 ft long, laid on a slope of 0.04, and have a projecting inlet and outlet. The culvert inlet bottom elevation is 302 ft with a head water elevation of 308.2 ft and a tailwater elevation of 302 ft. Use Ke = 0.8, Ko = 1.0. What is the discharge through the culvert (Use inlet control) with C₁ = 0.62. HW= 308.2 ft H=6.2 ft 302.0 ft BIBIE 3 Parallel CMP D= 48 inch S=0.04 TW 302.0 ft n=0.024 L = 80 ft
By considering the channel index as 5/3, the setting of an orifice type irrigation outlet to have proportionality is A 0.90 B 0.67 WRONG с 1 0.30 C CORRECT D 0.15

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS