A phenol standard with a concentration of 4.00 ppm has an absorbance of 0.424 at a wavelength of 460 nm using a 1.00-cm cell. A water sample is steam-distilled, and a 50.00-mL aliquot of the distillate is placed in a 100-mL volumetric flask and diluted to volume with distilled water. The absorbance of this solution is found to be 0.394. What is the concentration of phenol (in parts per million) in the water sample?

A phenol standard with a concentration of 4.00 ppm has an absorbance of 0.424 at a wavelength of 460 nm using a 1.00-cm cell. A water sample is steam-distilled, and a 50.00-mL aliquot of the distillate is placed in a 100-mL volumetric flask and diluted to volume with distilled water. The absorbance of this solution is found to be 0.394. What is the concentration of phenol (in parts per million) in the water sample?

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.1QAP

See similar textbooks

Similar questions

The determination of iron in wines was carried out by atomic absorption spectrophotometry, using the standard addition method. To do this, 10 mL of wine were placed in five 50 mL volumetric flasks; then 0, 5, 10, 15 and 20 mL of a 10 ppm iron standard solution were added to each of them. Next, they were gauged with distilled water and the absorbance was measured, obtaining the values of 0.040, 0.062, 0.081, 0.102 and 0.125 respectively. Calculate the regression parameters and obtain the iron concentration in the wine, in µg / mL.
The nitrite in a series of standard solutions (mg/L, n = 5) are converted to azo dye and the slope of the calibration curve is 2.0 ppm. A 10.00-mL mineral water sample is treated in the same way as standards and diluted to a final volume of 100.00-mL It gives an absorbance of 0.80. The absorbance of blank solution under the same conditions is 0.10. Calculate ppm (mg/L) of NO2 (46 g/mol) and the molarity of NaNO2 (69 g/mol) in the original sample
A solution in part C initially contains (4.0300x10^-4) molar SCN¯ and (2.880x10^-3) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (4.8600x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.40x10^3). Using the data provided above, determine the equilibrium constant for the reaction. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: х10 Answer
A solution in part C initially contains (4.1000x10^-4) molar SCN¯ and (1.180x10^-1) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (5.150x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.47x10^3). Using the absorbance and constant provided, determine the equilibrium concentration of FESCN2+, [FESCN2*]E. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: х10 Answer units
Suppose that you are trying to measure the concentration of SO2 in air. To do that, you followed the para-rosaniline method. The SO2 was collected in a 10-ml solution of HgCl4 2- then diluted to 25 ml after the addition of the appropriate reagents. The absorbance owas measured at 650 nm in a 2.0-cm cell, yielding a value of 0.535. A standard sample was prepared by substituting a 1.00 mL sample of a standard solution containing the equivalent of 15.00 ppm SO2 for the airsample. The absorbance of the standard is found out to be 0.191. Report the concentration of SO2 in the air in parts per million. The density of air is 1.19 g/L
The nitrite in a series of standard solutions (mg/L, n = 5) are converted to azo dye and the slope of the calibration curve is 2.0 ppm1. A 10.00-mL mineral water sample is treated in the same way as standards and diluted to a final volume of 100.00-mL. It gives an absorbance of 0.80. The absorbance of blank solution under the same conditions is 0.10. Calculate ppm (mg/L) of NO2 (46 g/mol) and the molarity of NANO2 (69 g/mol) in the original sample
A solution in part C initially contains (4.06x10^-4) molar SCN¯ and (2.960x10^-3) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (4.9800x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.8200x10^3). Using the data provided above, determine the equilibrium concentration of SCN", [SCN]E in this solution. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer units
The un-ionized form of the weak acid HA does not absorb in the visible region. When it ionizes, its conjugate base (A-) absorbs light strongly at 510 nm. The following data were obtained by measuring the absorbance at 510 nm of solutions with a concen- tration of 1.0 x 104 M HA in different pH buffers. pH Absorbance 2.0 0.00 3.0 0.00 4.0 0.00 5.0 0.025 6.0 0.180 7.0 0.480 8.0 0.570 9.0 0.595 10.0 0.595 11.0 0.595 12.0 0.595 What is the approximate pK of HA?
The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate solutions of known concentration. You are asked to analyze a Fe(SCN)2+Fe(SCN)2+ solution with an unknown concentration and an absorbance value of 0.4150.415 . The slope-intercept form of the equation of the line is ?=4558.4?+0.0147y=4558.4⁢x+0.0147 . The unknown was analyzed on the same instrument as the standard curve solutions at the same temperature. What is the Fe3+Fe3+ concentration of the unknown solution?
The following data were obtained from the spectrophotometric titration of Cu(II) and Ca(II) in an unknown solution. A 25.00 mL aliquot of the unknown was taken to which 50.0 mL of ethanolamine buffer and 25.0 mL of distilled water were added. The solution was then titrated with standard 0.2508 M EDTA solution. Plot the recorded data, absorbance against volume of EDTA in mL. Correct the absorbance for volume changes. Calculate the number of moles of Ca(II) and Cu(II) in the unknown sample. Vol of Titrant, mL Vol of Titrant, mL Abs Abs 0.0 0.416 12.5 0.886 2.0 0.415 13.0 0.923 4.0 0.409 13.5 0.958 6.0 0.416 14.0 0.979 8.0 0.535 14.5 0.969 10.0 0.690 15.0 0.971 11.0 0.770 15.5 0.964 12.0 0.840
Set up simultaneous equations for the analysis of Mo, Ti and V mixture by the peroxide method, using the data below. Standard solutions of Mo, Ti and V each at a known concentration of 2.00 mg of metal in a volume of 50.00 mL were measured at three wavelengths. Absorbances were measured to be: Metal 330nm 410nm 460nm Mo 0.416 0.048 0.000 Ti 0.130 0.608 0.410 N 0.000 0.148 0.200 An unknown solution was treated and diluted to a volume of 50.00 mL and the following absorbances were obtained: Abs at 330 nm = 1.189 Abs at 410 nm = 1.405 Abs at 460 nm = 0.952 Determine the mass (in mg) of each metal present in the unknown solution. Enter your numerical answer into the space provided: mass Mo= mg mass Ti = mg mass V = mg
As part of an investigation on Pb in biological ecosystems, some grasses that grew along the road and were exposed to emissions from motor gasoline were collected. 6.2501 g of grass were calcined to destroy all organic matter, the inorganic residue was properly treated and finally made up to 100 mL. An aliquot of 50 mL of this solution was read in an atomic absorption spectrophotometer registering an absorbance of 0.1250; then 0.10 mL of a standard solution of 55 µg of Pb / mL were added to the other 50 mL, with this fortified sample, another absorbance measurement was made, which was 0.1798. Calculate the µg of Pb / g of grass