02. A 300-mm square steel bearing plate lies between an 200-mm diameter wooden post and a concrete footing as shown. Determine the maximum value of the load P using allowable stresses of 12 MPa in wood and 4.5 MPa. 200 mm diameter P SUMMARY OF ANSWER: wooden post MAX. SAFE LOAD P = kN 300 mm x 300 mm steel bearing plate 300 mm x 300 mm concrete footing 300 mm 300 mm

02. A 300-mm square steel bearing plate lies between an 200-mm diameter wooden post and a concrete footing as shown. Determine the maximum value of the load P using allowable stresses of 12 MPa in wood and 4.5 MPa. 200 mm diameter P SUMMARY OF ANSWER: wooden post MAX. SAFE LOAD P = kN 300 mm x 300 mm steel bearing plate 300 mm x 300 mm concrete footing 300 mm 300 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
The turnbuckles in the diagram shown are tightened until the compression block DB exerts a force of 12,365lb on the beam at B. Member DB is a hollow shaft with an inner diameter of 1.0 inch and outer diameter of 2 inches. Rods AD and CD each have cross-sectional areas of 1.1 square inches. Pin C has a diameter of 0.78 inch. Determine the following: a.The axial stress, in psi, in BD. b.The axial stress, in psi, in CD.c.The shearing stress, in psi, in pin C.
A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall thickness of 0.125 inch. Segment BC is a solid rod of diameter 0.75 inch. Determine the normal stress in segment AB in psi. 0.125 in. 0.75 in. 4800 lb 2800 lb 1.5 in. B C |A -6 in.- -6 in. Your answer 2. In Problem 1, determine the normal stress in segment BC in psi. Your answer
Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN. Determine the smallest allowable outside diameter of the tube if the working stress is 110 MN/m2 Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa. 20 mm
A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim applying a force of 320 lbs including a dynamic load factor. The stand is a square tube with 5 inches outside length and 0.25 inches thickness. The distance from the edge of the rim to the middle of the square tube is 4 ft. Assuming the model is rigid, the normal stress at point A is most closely equal to: a. 1284 psi b. 1248 psi c. 1212 psi d. 36 psi A
The P load applied to a steel bar is transferred to the board by an annular washer. The diameter of the rod is 34mm and the inner diameter of the washer is 35.7 mm. Since it is known that the axial normal stress on the steel bar is 119 MPa, and the average bearing stress between the washer and the board should not exceed 34 MPA, how many mm is the smallest allowable outer diameter of the washer?
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 27 000 psi for the column, and the working bearing stress is 1300 psi for the concrete. 4 in. 3.5 in. i in. 1. Find the value of P in Ibs considering only the compressive stress in the column. a. 62549.27 Ibs b. 80342.78 Ibs c. 67124.11 Ibs d. 79521.56 Ibs 2. Find the value of P in Ibs considering only the bearing stress of the concrete. a. 63700 Ibs b. 49300 Ibs c. 72100 Ibs d. 58500 Ibs 3. Find the largest force P in Ibs that can be applied to the column. a. 63700 Ibs b. 49300 Ibs c. 62549.27 Ibs d. 80342.78 Ibs