. A single-phase 12.47 KV transmission line several kilometers long feeds a load from a substation. The line has a resistance of 2 Ω and a reactance of 20 Ω. Instruments at the substation indicate that the active and reactive power inputs to the line are 4 MW and 3 Mvar, respectively. Calculate a. The line current b. The power factor at the substation c. The active power absorbed by the load d. The reactive power absorbed by the load e. The line voltage at the load

. A single-phase 12.47 KV transmission line several kilometers long feeds a load from a substation. The line has a resistance of 2 Ω and a reactance of 20 Ω. Instruments at the substation indicate that the active and reactive power inputs to the line are 4 MW and 3 Mvar, respectively. Calculate a. The line current b. The power factor at the substation c. The active power absorbed by the load d. The reactive power absorbed by the load e. The line voltage at the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

An alternating voltage of 110 volts is applied to a circuit with resistance of 8.66 Ohms, inductance of 0.106 Henries, and capacitance of 75.8 microFarads. The frequency of the voltage is 50 Hz. Determine: a. The current in the circuit and its phase angle relative to the applied voltage. b. The voltage drop across each component of the circuit. c. The active and reactive power inputs to the circuit. d. Draw (Not hand-sketch) the equivalent power triangle. e. Is the RLC load of the circuit inductive or capacitive? Why?
Two reverse parallel scr are used to control the voltage on a 10 ohm load over a 230V, 50HZ 1- phase AC source, and triggering is done at 3O degrees for positive alterance. Calculate the effective (rms) voltage on the load. a) 230.34V b) 226.64V c) 220V d) 110.56V e) OV
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
A low voltage distribution transformer feeds two different loads with a three-phase line. The nominal voltage of the line is 400 Volt. The total length of the feeder is 500 m. The distance from the transformer to these loads is 140 m and 340 m, respectively. Their consumption is 11 kVA with a 0.8 lagging power factor and 10 kW with a 0.8 lagging power factor, respectively. The feeder's cross-section is 15 mm2 and the feeder's conductivity is 56 m/ohm.mm2. Find the following information. The distance from the transformer to the maximum voltage drop point is m The maximum voltage drop is Volt The power loss between the transformer and 11 kVA load is Watt.
Q A 50 Hz, 13.6kv, 3-phase arternator with grounded neutral hasinductance of 12 mH per phase and is connected to busbar 16]through a circuit breaker. The capacitance to earth between thealternator and the location of circuit breaker is o.03pF per phase.Neglect the resistance of the alternator. Determine the following:i) Maximum value of re-striking voltag. ."ro". the contactsof circuit breaker.i1) Frequency of transient oscillationsiii) Maximum value of RRRVir') Average RRRV upto the first peak of transientoscillations.
4.) A three-phase generator operating with a terminal voltage of 115V is connected to a three- phase transformer rated 7.5MVA 115/13.2kV. The transformer has a per-phase series impedance of 0.007+j0.075 pu and is connected to a distribution line with series impedance of 0.02+j0.1 pu per phase on a base of 10MVA, 13.2kV. The line supplies a balanced three-phase load rated 6MVA, 13.2kV with 0.85 lagging power factor. a. Draw and equivalent per phase circuit of the system indicating all impedances in per unit. Use 10MVA, 13.2kV as the base at the load. b. Find the current at the generator in amperes. c. Determine the voltage regulation at the load. 5.) If the transformer of 4.) is connected in A(115)-Y(13.2K), find the phase current of the generator.
An alternator with internal vallage of 125, p.u. and synchronous reactance of 0.4 p.u. is connected by a transmission line of reactance 0.1 p.u. c a synchronous meto having synchronous reactance 2.35 p u. and internal voltage of 0.85/6, p.u. If the real power supplied by the alternator is D 806 p... than (8, & is. degrees. (Round off to 2 decimal places) (Machines are of non-salient typa. Naglact resistances)
1.3 A 240 volts 50 Hz single phase ac source supplies a series load consisting of a resistor (40 ohms), a reactor (127.324 mH) and a capacitor (318.3 µF). Suppose that the frequency of the source can be varied at will. 1.3.1 Determine the maximum load current. 1.3.2 Determine the source frequency for maximum load current. 1.3.3 What is the name of this frequency? 1.3.4 Determine the load power factor. 1.3.5 What is the name of the source
a. i. Why do power systems operate in an interconnected arrangement? ii. How is the frequency controlled in a power system? iii. What is meant by the stiffness of a power system? b. Two 50 Hz power systems are interconnected by a tie-line, which carries 1000 MW from system A to system B, as shown below. After the outDage of the line shown in the figure, the frequency in system A increases to 50.5 Hz, while the frequency in system B decreases to 49 Hz. i. Calculate the stiffness of each system. ii. If the systems operate interconnected with 1000 MW being transferred from A to B, calculate the flow in the line after outage of a 600 MW generator in system B. 1000 MW A В
QUESTION 1 Two magnetically-connected circuits have the following characteristics: . A series-opposing connection of coils (dot convention). The primary side is connected to a voltage source that has a magnitude of 230 V and a phase angle of 45 degrees. . The primary-side inductive reactance is jXL1 - j8 Ohm. . The secondary side is connected to a resistive load of 10 Ohm. . The secondary side inductive reactance is jXL1 =j5 Ohm. . The mutual inductive reactance is jM=j1 Ohm. The magnitude of the voltage across the resistive load is:
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.