wo identical cylindrical jobs are turned using (a) a round nosed tool of nose radius 2 mm and (b) a sharp corner tool having principal cutting edge angle = 45° and auxiliary cutting edge angle = 10° If the operation is carried out of the teed of 0.08 mm/rev will Find the height at micro irregularities on the machined surfaces (in mm) in the two

wo identical cylindrical jobs are turned using (a) a round nosed tool of nose radius 2 mm and (b) a sharp corner tool having principal cutting edge angle = 45° and auxiliary cutting edge angle = 10° If the operation is carried out of the teed of 0.08 mm/rev will Find the height at micro irregularities on the machined surfaces (in mm) in the two

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Similar questions

The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate: 4.3. Maximum fluctuation of energy of the flywheel. 4.4. Mass of the flywheel having radius of gyration of 1.5 m.
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
An Aluminium workpiece of 175 mm length is machined in a lathe, where the plain tuming openatnin done with th spend steel single point cutting tool. The diameter of the workpece got reduced by 5 mm durng thin operation As per the wng the required machining lengthis 103 mm and the final diameter is 16 mm, The lathe was set to operate at a spede speed u 2550 rpm and the camage was set to move with an aal speed of 415 mm/min auaomatically. he aut pownt is timated to & Ws/ mm Calculate: (a). Cutting speed (b). Depth of cut (d. Material Removal Rate (d). Cutting time (e). Net power required
A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
A twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece. Both holes are twist drill with 118° point angles. cutting speed for material is 230 ft/min. The rotation speed of each spindle can be configured individually. The feed rate of both holes must be set to the same value, since both spindles go down at the same speed. The forward speed is set in such a way that the speed total metal removal does not exceed 1.50 in3 /min. Determine: a) the velocity maximum feedrate (in/min) that can be used, b) the individual feedrates (in/rev) that result in each hole and c) the time required to drill the holes.
A motorised metal guillotine machine is required to cut 45 mm diameter hole ina plate of 20 mm thickness at rate of 35 holes per minute. It requires a torqueof 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second andthe speed of its flywheel varies from 165 rpm to 145 rpm, calculate:1.Energy required to cut a hole.2.Energy required for cutting work per second.3.Maximum fluctuation of energy of the flywheel.4.Mass of the flywheel having radius of gyration of 1.5 m.