What is the voltage at node 2 in the circuit

Q: Reprogramming is possible in CNC (Computer numerical control) systems. Select one: True False

A: Reprogramming is not possible on CNC systems because once it is activated it can’t be undo

Q: A(n) __________ switch uses a rotary motion to open and close contacts

A: Que :  A________ Switch uses a rotary motion to open and close contacts. Ans : A Rotary Switch uses…

Q: type of system,the input and output have direct connection in In between. O a. Dynamic O b. Closed…

A: Hi and thanks for the question. Since you have asked multiple questions, we will solve the first…

Q: the mode of torsióna הבהרו ar

A:

Q: Discuss the principle operation of the AVR?

A: AVR stands for the automatic voltage regulator. It is an electronic device that automatically…

Q: Draw a series circuit with a thermostat,a low-pressure switch, and a highpressure switch used as…

A: To draw this circuit, we have to consider the function of each component. The thermostat is used to…

Q: The alternating current produced by the AC generatoris rectified into DC, or direct current, through…

A: As rectifiers, transmission limiters, power supplies, switches, signal modulators, signal mixers,…

Q: 15. When you measure the voltage drop across a set of contacts, you're O A. measuring the equivalent…

A: When you measure the voltage drop across a set of contacts, you're A. measuring the equivalent…

Q: Explain the operation of the circuit presented below. For each component, indicate name, drive mode,…

A: Given : To find : Working of the circuit

Q: Where can you find a resistor in Multisim Live Online Circuit Simulator? a. Indicators b. Passive

A:

Q: A three-pole contactor would allowhow many paths for current flow?

A: A  three-pole contactor is a device used to turn off or turn on the three phase load. When the…

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: What is the peak voltage of a 120V RMS AC voltage?

A: Given Vrms=120VAssuming that AC signal to be sinusoidal,

Q: With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is…

A:

Q: ons: In what situations would a circuit with multiple system pressu Are there any disadvantages to a…

A: 3. Hydraulic pressure is expressed as a force per unit of area, such as bar (kg/cm2) or PSI…

Q: All terminals have a defined wire size range. If I had a wire of 2.0mm / 15 AWG, what terminal…

A: Calculate the cross-sectional area of the wire by using the 15 AWG. 15 AWG=1.65 mm2

Q: What happens when the low-voltage current flow inthe coil primary winding is interrupted by the…

A: Primary winding and scendary windings aare used to increases or decreases the current and voltage…

Q: 5. Determine the Thevenin's and Norton's equivalent circuits across a-b. 122 a 8A 12

A:

Q: is used to convert resistance value into voltage value.

A:

Q: what would be the resistance of a circuit that is open

A: For an open circuit, no current will pass through the circuit.

Q: Reduce the combinational logic circuit in figure 1 to minimum forn Figure 1 A D.

A:

Q: Introduction about Pnuematic Control of Double Acting Cylinder Using Counter and Timer

A: illustrating with the examples: Use a 5/2 pneumatically actuated control valve and use limit…

Q: Find the currents 11 and 10 in the circuit using current division

A: Solution is given below.

Q: e output voltage of

A: Need to find Output voltages.

Q: A transformer has a primary voltage of 480 volts and a  secondary voltage of 20 volts. What is the…

A: Electric Energy transformed from one alternating-current circuit to one or more another circuit is a…

Q: There is an ambient temperature of 65°C with a temperature rating of the conductor as 75°C. What is…

A: Introduction: Heat transmission, whether through conduction, convection, or radiation, is…

Q: Explain briefly, Meter out and bleed off circuits with neat circuit diagram.

A: Given: Explain briefly, meter out and bleed off circuit with neat sketch diagram.

Q: In Wheatstone bridge circuit ,the output voltage under balanced condition is

A: ans:-  When the output voltage (V0) between terminal A and B equal to zero.

Q: A circuit contains two un-equal resistances in series Select one: O A. " larger potential develops…

A: Given: A circuit contains two un-equal resistances in series

Q: If IC=3.95mA and IB=50µA, then IE calculates out to be: * 3.45MA 4mA 79mA .075mA

A:

Q: dosed loop frequency resp

A: Solution given below .

Q: v=0 AE- +24V 2 OV 14 3 = K1 2 1Y 1 4 can you please explain how this circuit works 4 5 15$

A: Concept: 1) In the given pneumatic circuit, there is an 3/2 solenoid cum plunger operated…

Q: The current which that passed :through the interface must be

A: The current which that passed through the interface must be zero.

Q: In the experiment No.1, the power measurement using two wattmeter method for star connected load,…

A: As per the assumptions taken while doing the experiment the value of all currents are equal and…

Q: A household three-way switch is used to allow lights to be controlled from two loca- tions (e.g, at…

A: Solution: 1. When both switches are connected to the left terminal (Lamp is OFF) 2. When switch 1…

Q: Write any one disadvantage about core and shell type transformer.

A: In Core type transformers, the rectangular frame is made up by laminating the magnetic core.…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.