What is the most probable cause of this casing failure? 0253 The pipe was under tension, decreasing the burst resistance. The pipe was under tension, decreasing collapse resistance. The axial stress in the pipe have exceeded the yield stress. The pipe failed due to excessive pressure from the interior.

What is the most probable cause of this casing failure? 0253 The pipe was under tension, decreasing the burst resistance. The pipe was under tension, decreasing collapse resistance. The axial stress in the pipe have exceeded the yield stress. The pipe failed due to excessive pressure from the interior.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? * Your answer A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 5 MN/m^2. (a) Determine the safe stress between the tangential and longitudinal sections in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MPa? (c) If the internal pressure were increased until the vessel burst,…
Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to withstand an internal pressure of 8 N/mm². The maximum hoop stress i the section is not to exceed 35 N/mm² probaken (b).Determine the maximum and minimum hoop stress across the section of a pipe of 400 mm internal diameter and 100 mm thick, when the pipe contains a fluid at a pressure of 8 N/mm². Also sketch the radial pressure distribution and hoop stress distribution across the section
a.) What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? b.)What is the normal force distributed to Red Brass Hollow Tube 'B' (in kips)? c.)What is the normal stress produced in Stainless Steel Solid Post 'A' (in psi)? d.)What is the normal stress produced in Red Brass Hollow Tube 'B' (in psi)?
A 2024-T4 aluminum tube with an outside diameter of 2.4 in. will be used to support a 30-kip load. If the axial stress in the member must be limited to 17.5 ksi, determine the wall thickness required for the tube.
What is the importance of the maximum shear stress for thick walled cylinders?
Problem 1 Please choose the correct answer and also write down your solution. (1) A cylindrical tank is required to contain a gage pressure 630 kPa. The tank is to be made of A516 Grade 60 steel with a maximum allowable normal stress of 150 MPa. If the inner diameter of the tank is 2.8 m. what is the minimum thickness of the wall? a. 11.76 mm b. 5.88 mm c. 11760 mm d. 0.00588 mm (2) A cylindrical tank is made of A516 Grade 60 steel with a maximum allowable normal stress of 150 MPa. If the inner diameter of the tank is 4.1 m and the thickness is 1.5 cm. What is the maximum allowable gage pressure? a. 1.097 MPa b. 549 kPa c. 109.76 MPa d. 109.76 kPa (3) A spherical pressure vessel is required to contain 1.4 m³ of compressed natural gas at 21 MPa. If the tank is made of A516 Grade 60 steel with a maximum normal stress 150 MPa. What is the required thickness of the tank wall? a. 97.16 mm b. 9.716 mm c. 4.858 cm d. 53.47 mm
Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A and loaded as shown. Which of the following gives the maximum average normal stress in the system shown? 6P 4P A5.5 P/A B.4.5 P/A 3A 2A A 3P C.4 P/A D.3 P/A 4P 6P Which of the following is the highest value of stress within the strain hardening region of a typical elasto-plastic material subjected to tensile test? A. Elastic Limit B.Yield Stress C.Ultimate Stress D.Proportional Limit What is the lateral strain of a uniaxially loaded member if its longitudinal strain is 0.02 and its Poisson's ratio is equal to 0.3? A.+0.006 B.-0.006 C.+0.667 D.-0.667 Which of the following is the highest value of stress within the elastic region of a typical elasto-plastic material subjected to tensile test? A.Yield Stress B.Elastic Limit C.Ultimate Stress D.Proportional Limit
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears a determine the minimum force P required to punch the slot. Punch O 1051 KN O 766 kN O 649 kN O 717 KN O 979 KN Slug Plate 20 mm 75 mm Plan view of slug + a stress of 360 MPa,
8-6 The open-ended polyvinyl chloride pipe has an inner diameter of 4 in. and thickness of 0.2 in. If it carries flowing water at 60 psi pressure, determine the state of stress in the walls of the pipe.
Determine the cracking moment for the figure shown if it is a normal weight concrete with fc=4,000psi. 8 in. 8 in. 24 in. 3 #10 8 in. 3 in.: ⒤갓⒤갓⒤뀐⒤뀐⒤ 6 in. 15 in. -16 in.-
Determine the safe wall thickness of a 35 inches steel tank with internal pressure of 8.02 Mpa. The yield stress of material is at 300 Mpa. The factor of safety to use is 2.5. d. 21.6 mm c. 28.4 mm b. 26.8 mm a. 29.7 mm
Problem 1: Determine the cracking moment for the following beam sections shown if f 'c = 28 MPa. wwww w 400 mm 800 mm 5-25 mm [ 60 mm 600 mm