Water flows through the branching pipe as shown in Figure below. If viscous effects in the system are negligible, determine the pressure in gage at section (2), P2, and the pressure in gage at section (3), P3. Az = 0.035 m? Z3 = 10 m Q1 = 1 m/s A, = 0.1 m? P1 = 300 kPa 21 = 0 (3) V2 = 14 m/s A2 = 0.03 m2 Z2 = 0 (1) (2)

Water flows through the branching pipe as shown in Figure below. If viscous effects in the system are negligible, determine the pressure in gage at section (2), P2, and the pressure in gage at section (3), P3. Az = 0.035 m? Z3 = 10 m Q1 = 1 m/s A, = 0.1 m? P1 = 300 kPa 21 = 0 (3) V2 = 14 m/s A2 = 0.03 m2 Z2 = 0 (1) (2)

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the water is following. The pipe is located at 5 metre above the datum line. The sum of total head and stagnation head is m. (g = 10 m/s?). (assume 1 bar = 105 Pa) %3D
The gate AB shown in figure is hinged at A and kept closed by a force P at B. Compute for the Hydrostatic Force acting on the side of the gate AB. (Given: p = -18.46 kPa, OIL SG = 0.8) p-18.46 Pa Figure 34(01)A Ol, s-0.8 7 m 6m 2m Answer:
... T A 30° 2.5m Water hinge L= 2m In the figure shown, a quarter circle gate AOB is hinged at point B. Force "T" at point A is placed at a 30 degree angle from the horizontal to keep the gate in equilibrium. Determine the following: a) Total hydrostatic force "F" = Blank 1 KN b) Force "T" to make the system in equilibrium = Blank 2 KN Blank 1 Add your answer Blank 2 Add your answer
Situation XX: In the figure shown, z, = 4 m, length of pipe from the reservoir to the pump is 120 %3D m, from the pump to the nozzle is 1000 m. The diameters of pipes are 0.60 and 0.45 m respectively. The gage pressure at B (the suction side of the pump) is -64 KPa. Neglect minor losses. В C P. 0.45 m diam. LCD = 1000 m %3D Zp = 4 m f = 0.02 0.60 m diam. LAB = 120 m f = 0.02 %3D 52. Compute the velocity of water in pipe AB. a. 2.297 m/s b. 1.452 m/s c. 3.147 m/s d. 2.672 m/s 53. Compute the velocity of water in pipe CD. a. 1.23 m/s b. 4.08 m/s c. 3.56 m/s d. 5.59 m/s 54. Compute the discharge of the pipe from A to B due to pumping. a. 0.65 m3/s b. 0.45 m3/s c. 0.89 m³/s d. 0.25 m3/s 60 m, f= 0.02 m and loss of head ith
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine a) FMY (N) b) Fpx (N) c) Fpx (N) de = 100 mm da = 150 mm 30° A
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
CORRECT LETTER PLS 1. In a system with 4 reservoirs and 1 pipe junctions, how many hydraulic headloss equations are formulate? A. 3B. 2C. 1D. 4E. 5 2. In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is true and JB is false B. BJ is true and JB is true C. BJ is false and JB is false D. BJ is false and JB is true 3.which of the following is always the same for horizontal closed conduit? A. Total headB. Velocity headC. Elevation headD. Pressure head
• A wooden storage vat full of oil sg=0.80 is in the form of a frustum of a cone, 2m diameter at the top and 4m diameter at the bottom, and 3m high. It is provided with two steel hoops one at top and one at the bottom. a. Compute the hydrostatic force on the side of the container. b. How high is the said force above the bottom? c. Compute the force in the bottom hoop.
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine The pressure at section B, ps (kPa) FMx (N) FMY (N) de = 100 mm da = 150 mm 30°
Q1: For the set up shown in the following figure. Determine the total head, pressure head, elevation head at points A, B, C, D, E and F and seepage velocity of flow. 4.8 Sell, K-0.51 3.C BO D 3.6 2.4 1.8 1.2 0.6 0 Datum
Part A 100 mm Determine the volumetric flow of water through the crack. μÅ h Express your answer to three significant figures and include the appropriate units. 1.02.10-6 m³/s Submit Previous Answers Request Answer ?
Assignment -2: If the pressures at pipes 1 and 4 are 30 kPa and 120 kPa respectively, determine the length AB. Oil, S = 0.9 Hg 0.6