Use the interactive area below to draw a Free Body Diagram to describe the 2M box resting on the horizontal frictionless surface. For this task, assume that the weight of the suspended 1M box is sufficient to cause the 2M box to accelerate to the right. (The actual behavior will depend upon the magnitude of the applied force, F, and the angle, 0.) In this problem we will use the notation F1M and F 2M to represent the weights of the 1M and 2M boxes, respectively.

Use the interactive area below to draw a Free Body Diagram to describe the 2M box resting on the horizontal frictionless surface. For this task, assume that the weight of the suspended 1M box is sufficient to cause the 2M box to accelerate to the right. (The actual behavior will depend upon the magnitude of the applied force, F, and the angle, 0.) In this problem we will use the notation F1M and F 2M to represent the weights of the 1M and 2M boxes, respectively.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Problem 1: A block with a mass of m rests on a frictionless surface and is subject to two forces acting on it. The first force is directed in the negative x-direction. The second acts on the body at an angle 0 measured from horizontal, as shown. If necessary, use Fs and Fk for the forces of static and kinetic friction. L. F Please use the interactive area below to draw the Free Body Diagram for this block, assuming it is in static equilibrium. FBD : Fn, F1, Fg, F2, Fs, Fk, a, v 45, 0, 90, 135, 180, 225, 270, 315, 0 Force Labels: Angle Labels: m.
Consider the system in the picture below: a cart of mass M with a static friction coefficient u is connected through a massless string to a hanging mass m. M is a capital letter, m is lower case. Write them as such, or vour equations will be confusing, M We want to find the maximum value of the hanging mass m such that the system is in equilibrium. 1. Free body diagram (FBD): Draw a FBD for each: the Cart and the hanging mass. Clearly show all the forces. 2. Clearly write the equilibrium equations for the cart in the horizontal and vertical direction. 3. Clearly write the equilibrium equation for the hanging mass. 4. Solve the system of the three equations above for the hanging mass m. Show your calculation to get credit. 5. What would happen if mass m exceeds this value? Explain.
Now set the Mass back to 2.5 kg and the Coefficient of Kinetic Friction back to 1. Let the simulation run once again by clicking on Start. Observe how the friction force (given by the length of the fk vector) changes as the box speeds up. QUESTION: How does the magnitude of the friction force change as the velocity increases?
Three cables are used to hold a hot-air balloon in place. The tension in the cable AD is 658 N. Draw the Free Body Diagram at A. Upload this along with your all your workings for this problem to the dropbox. What is the tension in the cable AB? Enter using 3 significant figures. What is the tension in the cable AC? Enter using 3 significant figures. What is the vertical force V exerted by the balloon at point A? Enter using 4 significant figures.
Blocks A and B are held on the palm of your outstretched hand as you lift them straight up atconstant speed. Assume mB>mA and that mhand=0.a. Draw separated free-body diagrams for A, B and your hand. Show all vertical forces andmake sure the vector lengths indicate the relative sizes of the forces.b. Rank in order from largest to smallest all of the vertical forces. Explain your reasoning.Now the hand is lifting the blocks so they have an upward acceleration.c. Draw separated free-body diagrams for A, B and your hand. Show all vertical forces andmake sure the vector lengths indicate the relative sizes of the forces.d. Rank in order from largest to smallest all of the vertical forces for when the block isaccelerating. Explain your reasoning.
A contestant in a winter sporting event pulls an m kg block of ice across a frozen lake by applying a force F at an angle θ above the horizontal as shown. Assume that the coefficient of static friction for ice on ice is 0.0300, and the coefficient of kinetic friction for the same is 0.0100. Let to the right be the positive x direction and up be the positive y direction for your equations. Please use the interactive area below to draw a free body diagram to represent the situation where the contestant is pulling, but the block has not yet started to move. Use Fs for the force of static friction and Fk for the force of kinetic friction if they are needed for your free body diagram. 17% Part (b) Select the correct expression for the net force in the horizontal direction, ΣFx. 17% Part (c) Select the correct expression for the net force in the vertical direction, ΣFy. 17% Part (d) Obtain a numeric value, in newtons, for the magnitude of the maximum applied force, F, consistent…
Consider the following hanging mass system for the following problems. Part A Before answering the questions below, draw two separate free-body diagrams of ring C and then ring B. Be sure the FBDS are neat a properly labeled. You will turn them in with your written work. Deturmine the tension developed in cable CB if cylindar E weighs 36 lb and e = 15°. (Figure 1) It vec FCB Ib Submit Request Answer Part B If cylinder E weighs 36 lb and 0 = 15°, determine the weight of cylinder F. Express your answer with the appropriate units. Figure vec WF Ib Submit Request Answer 30° 45° B. Provide Feedback Next > E F
The previous step focused on friction for horizontal surfaces. As we discussed above, angled surfaces like the wedge below have different considerations. FN = mg cos(0) F₁ = mg F₁ = ? F₁ = ? Fy=mg cos(0) Specifically, we have the following considerations. 1. The normal force is not equal to mg. 2. There is a force acting along the angle of the wedge due to gravity. What is the coefficient of static friction ? Fx = mg sin(0) Let's consider the implications of this type of problem with the following examples. For all of the examples, the box has a mass of 25 kg. Imagine the box is on a surface that allows you to adjust the incline angle, 0. You find the maximum angle where the box remains stationary. That is, at any higher angle, and the box begins to slide. The static friction force at this maximum angle is 150 N. What is the angle 0 (in degrees)? Now you raise the incline to an angle of 60° greater than the angle of maximum static friction found above. At this angle, the box slides…
Consider the system shown in the figure (Figure 1). Block A has weight w, and block B has weight wg. Once block B is set into downward motion, it descends at a constant speed. Assume that the mass and friction of the pulley are negligible. Part A Calculate the coefficient of kinetic friction u between block A and the table top. Express your answer in terms of some or all of the variables wa (double-u subscript A), WB, and g (the acceleration due to gravity). • View Available Hint(s) Submit Part B Complete previous part(s) Part C Complete previous part(s) Provide Feedback Figure B
Just need part D and E answered Consider a 5 kg mass placed on a frictionless incline that makes an angle of 30 degrees with the horizontal. A rope is attached and positioned over a pulley at the top of the incline. A 6 kg mass is suspended from the free end. a) On a separate diagram, draw the FBD of the hanging block, , and label all the forces acting on it. b) On a separate diagram, draw the FBD of Block and label all the forces. c) Write down Newton’s second law for each block, and for each relevant co-ordinate axis. d) From your equations in part d), write down an expression for the acceleration of the system. e) Calculate the acceleration and the tension in the chord
PROBLEM SET # 8: PARTICLE UNDER A NET FORCE On the space provided, present correct and organized solutions to the following answered problems. Box the final answers. Detach each page neatly and submit to your instructor. A 2.5-kg concrete block sliding on a vertical wall is being acted upon by a force P as shown in the figure below. Assume that the coefficient of kinetic friction between the 2. concrete block and the wall is 0.88. 148° (a) Draw the free-body diagram of the concrete block. (b) If the normal force exerted by the wall to the concrete block is 20.0 N, what would be the magnitude of the external force P, and (Ans: 37.74 N) (c) The acceleration of the block? (Ans: -15.56 m/s)
An object of mass M is attached to a string. The length of the string is r and has no mass. The objects moves in a vertical circle counterclockwise as shown. When the ball is at point F, the string is horizontal. Point E is at the bottom of the circle and point Dis at the top of the circle. Air resistance is negligible. Express all algebraic answers in terms of the given quantities and fundamental constants. On the figures below, draw and label all the forces exerted on the ball when it is at points F and E, respectively.