Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.5 in.2 and an elastic modulus of 2400 ksi. Bar (2) has a cross-sectional area of 0.832 in.2 and an elastic modulus of 3110 ksi. Assume L1-16 in., L2-38 in., Q=8.2 kips, P-3.7 kips, and R=15.6 kips. Determine the horizontal deflection of end C relative to end A. (1) (2) L2 in. Answer: uCA =

Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.5 in.2 and an elastic modulus of 2400 ksi. Bar (2) has a cross-sectional area of 0.832 in.2 and an elastic modulus of 3110 ksi. Assume L1-16 in., L2-38 in., Q=8.2 kips, P-3.7 kips, and R=15.6 kips. Determine the horizontal deflection of end C relative to end A. (1) (2) L2 in. Answer: uCA =

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and poisson's ratio is 0.30.
X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.42 in.and an elastic modulus of 2180 ksi. Bar (2) hasa cross-sactional area of 1139 in.and anelastic modulus of 4150 ksi. Assume l-23 in., L-41 in, Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Datermine the horizontal deflection of end Crelative to end A P R (1) (2) Answer: uga in.
Q2/Show the mechanical properties changes during tensile test of a metal specimen. Write the mathematical relationships. 443X
A round aluminum alloy bar with a 0.25-in. diameter and a 1-in. gauge length was tested in tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table P4.8.Using a spreadsheet program, obtain the following: a. A plot of the stress–strain relationship. Label the axes and show units. b. A plot of the linear portion of the stress–strain relationship. Determine modulus of elasticity using the best fit approach. c. Proportional limit. d. Yield stress at an offset strain of 0.002 in/in. e. Initial tangent modulus. f. If the specimen is loaded to 3200 lb only and then unloaded, what is the permanent change in gauge length? g. When the applied load was 1239 lb, the diameter was measured as 0.249814 in. Determine Poisson’s ratio.
QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
2- the rubber blocks shown in Figure 2 are used in a double U shear mount component. The dimensions of the rubber blocks are 15 x 21 x 25 mm and the applied load of 650 N cause the upper frame to be deflected by 5 mm. ↓ Double U anti-vibration shear mount 15 Shear deformation of blocks 25 Rubber block dimensions 21 오 Figure 2 (a) determine the average shear stress and shear strain in each of rubber blocks (b) determine the shear modulus G of the rubber material used in this component.
7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses in the two materials with an applied load of 45,000 lbs. 45,000 lbs 3.5"Ø 3.0"Ø Steel Aluminum
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
The beam is made from a material that can safely support a tensile or compressive stress of 350 MPa. a) Based on this criterion, determine the largest force, F, the beam will safely support if it has the cross- section (a). b) What is the largest allowable F for cross-section (b) Recall for a rectangle: I = bh³/12 1.0 m- 60 mm 23.3 mm Figure 1 Cross-section (a) -0.63- 10 mm 10 mm 40 mm 10 mm -50 mm - Figure 2 Cross-section (b)