Triangle ABC has sides AB = 40 cm, BC = 60 cm, and angle B = 45 degrees. Comput

Q: METHOD OF FRAMES

A:

Q: An Egyptian pyramid has a square base and symmetrical sloping faces. The inclination of each sloping…

A:

Q: Given data Stress=202 N/mm² Area = 3 mm² 2 Find Force.

A:

Q: F. A living room is 7.2 m long and 4.5 m wide. What size would it be on a plan drawn to a scale of…

A:

Q: 15. Simplification, 16. Gravity 17. Space Utilization 18. Unit Size

A:

Q: Given data: Force=2 N Area =0.2 mm2 Determine stress

A: Given:-  Force = 2 N Area = 0.2 mm2 To Find:-  Stress

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 210 mm respectively. The clearance…

A: Given data, D = 120 mm = 0.12 m L = 210 mm = 0.21 m Vc = 0.00029 m3 Find: V = ?

Q: The top of a ladder weighing 20 kg and 6m long rests against a vertical wall and the foot of the…

A:

Q: g/mol. compute its theoretical density, and compare the answer its measured density.

A:

Q: Given data: Applied force=3N Distance covered%3D5 m Determine work done

A: Given data : Distance covered=d Applied force=F   To find : Work done

Q: .Find (ly) for the shaded area Y 2m 2 6m 1 3 оз 3m 3m 3m

A: Mass moment of inertia measures a body resistance towards rotational motion. If a body have more…

Q: According to the following figure, calculate the horizontal and vertical force on a circular segment…

A: Given: The radius of the segment, r = 2 m The width of segment, b = 5 m

Q: Boat is pulléd into a dock by means of a winch 2 meters above the deck of the boat (see figure). The…

A:

Q: A master cylinder has 150 pounds per square inch of pressure applied to the piston. The diameter of…

A:

Q: n, BC = 5 m)

A:

Q: s shown in Figure Q1. Dimensions th of 90 MPa. The diameter of the etion at A:

A:

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: Given data : Area=3 cm2 Stress-40 N/cm2 Find force

A: Given data : Area=A Stress=σ   To find : Force

Q: 5 m/s 1 m Figure Q3

A: Answer: (a) The wooden box A speed just before the impact is 3.6370 m/sec. (b) After the impact, VA…

Q: Compute the height in feet of a high building if the pressure at the ground floor is 30 in Hg and at…

A:

Q: a, in mm (round off to one decimal place), such that maximum actuating force P is 2000 N, is

A: Given data;  FBD of drum,

Q: Calculate the K value for the hollow square shape, if the height is 25 mm and thickness is 2 mm.…

A:

Q: Convert 159 cubic micrometers, μm3 to cubic meters, m3

A: Given 159μm3 To find The value in m3

Q: Calculate the work done by a 47 N force pushing a pencil 0.26 m.

A: Product of force and distance travelled in the direction of force by object is known as work.

Q: Find the volume of a pyramid whose base is a triangle of edges 3 cm, 5 cm, and 7 cm, and altitude is…

A: 1) Given that, Edge length of  triangle base=3 cm, 5 cm, 7 cm,Altitude of pyramd, h=12 cm Calculate…

Q: Calculate Iyy for the shaded area shown. 45 cm 15 cm 30 cm

A:

Q: a tractor applied 20 N force to displace a box 20 m. calculate the work done.

A:

Q: 18 k 1. Solve the Concurrent Force system: 26 ngle

A: Given:

Q: A stone weighs 600 N, and when it was lowered into a square tank 610 mm on a side, the weight was…

A:

Q: Find the total magnitude of force, EFy acting in y-direction (answer in newton, N with a single…

A: In the given problem, following formulae for determining the resultant will be used Magnitude of the…

Q: 2.5 m

A:

Q: An isosceles triangle has legs 10 cm. The base decreases at the rate of 4 cm/sec. Find the rate of…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: A rectangular box with a square base is to have a volume of 20 cubic feet. The material for the…

A: Given data: V=20 ft3Cbase=30 ctsft2Cside=10 ctsft2Ctop=20 ctsft2

Q: The scale of an aerial photograph is 1:15,000, In the photo you measure the length of a bridge to be…

A: Given data: Scale=1:15,000L=0.25 in Need to determine the length of the bridge in feet.

Q: on is given

A:

Q: Draw a circular hole of 2cm deep and give dimensions to it.

A:

Q: Determine I for the thin-walled sections shown in Figures 8.9(a) to 8.9(c), where the wall…

A: Given data To determine the moment of inertia about x axis of the given section.

Q: Given data : Force=3 N Area=2 m2 Determine stress

A:

Q: For the given data, the value of :distance L is Given flexural Sreas= Sees Ps: cAsectte

A: The given simply supported beam is as shown below, Since this is a symmetric beam with udl over its…

Q: A body weighing 2,225N is being dragged along a rough horizontal plane by a pull of 445N directed at…

A:

Q: Calculate the work for the expansion in the process to 2 decimal places.

A: Thermodynamics : It is a branch of science which deals with work , heat , energy.  Also it studies…

Q: The sides of a square lot having an area of 2.25 hectares were measured using a 100m tape that was…

A: Area of square lot, A=2.25 hectares= 10000 sq.m Length of the tape, L=100 m Tape is short by,…

Q: 2.) Calculate the resultant force. (10PTS.) D = 500lb A = 2000lb 45°

A: Given

Q: Find results of forse

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.