To obtain friction factor, f, we need to know the Q, D, and ks in a given fluid flow. But if Q is unknown, select the most appropriate answer. D3/2 2ghf Still, we can get f by using k/D (on the right axis) and Ref = (on the top axis). O When Q is known, but D is unknown, we can get f from the Moody diagram. When Q is unknown, we cannot get Re, so we cannot get f from the Moody diagram. O None of the answers are correct.

To obtain friction factor, f, we need to know the Q, D, and ks in a given fluid flow. But if Q is unknown, select the most appropriate answer. D3/2 2ghf Still, we can get f by using k/D (on the right axis) and Ref = (on the top axis). O When Q is known, but D is unknown, we can get f from the Moody diagram. When Q is unknown, we cannot get Re, so we cannot get f from the Moody diagram. O None of the answers are correct.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the beam shown in (Figure 1). Suppose that M=5.5 kN m. EI is constant. Assume that EI is in kN m². Use the moment-area theorems to solve this problem. Follow the sign convention. Figure 6 m B 3 m M Determine the displacement at C Express your answer using three significant figures. Δε = Submit Part C -27 0A ΑΣΦ X Incorrect; Try Again; 2 attempts remaining Submit vec Previous Answers Request Answer Determine the slope of the beam at A. Express your answer using three significant figures. IVE ΑΣΦ ↓↑ vec 8.5 Previous Answers Request Answer Answers X Incorrect; Try Again; 5 attempts remaining Part D Complete previous part(s) ? X 1 kN-m³ EI 1 kN-m² EI
To obtain friction factor, f, we need to know the Q, D, and kg in a given fluid flow. But if Q is unknown, select the most appropriate answer. O When Q is unknown, we cannot get Re, so we cannot get f from the Moody diagram. 2gh D3/2 Still, we can get f by using k/D (on the right axis) and Ref: (on the top axis). L O None of the answers are correct. When Q is known, but D is unknown, we can get f from the Moody diagram.
7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched element and through a force balance, show that the velocity distribution across the layer is: d X y sin e (b2 - s2) Free U = Surface b. Derive an expression for the liquid velocity surface. at the free t dx ys dx Fixed c. Derive an expression for the discharge per unit width. d. Derive an expression for the shear stress at the fixed wall. Wall b
3. Find the least value of P that will just start the system of blocks shown below moving to the right. The coefficient of friction under each block is 0.30. B F- 0.30
2. Find the least value of P required to cause the system of blocks shown in figure to have impending motion to the left. The coefficient of friction is 0.2 under each block.
Find the fundamental frequency of the torsional system shown below, using Dunkerley's formula for the following data. J₁ =J2 = J3 = Jo and k₁₁ = kt2 = k+3 = kt. Ma Mp M12 Compressor (1) Turbine (J₂) Generator (3)
Question 2 Determine the moment of inertia of the area about the x axis as shown in Figure Q2. Determine b value and solve the problem in two ways, using rectangular differential elements: (a) having a thickness of dx, and (b) having a thickness of dy. 6 m b b Figure Q2. y = 6-6x²
The figure shows a cantilever of length L= 4 m consisting of steel angles size of 100 x 100 × 12 mm mounted back to back. The cantilever is subjected to a point load P= 1500 N acting at a = 2.5 m and a distributed load w= 1100 N-m-. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P a В Find the deflection at B. The deflection at B is – 4.46 mm.
Consider the beam shown in (Figure 1). EI is constant. Part A Determine the expression for the elastic curve using the coordinate x1 for 0 ? Determine the expression for the elastic curve using the coordinate 2 for 0 < x2
Q1) Choose_right answer and complete the sentences Lo is the formula for friction factor(f). 2. A water flows through a pipe at a velocity 2 m/s. The pressure gauge reading is 2 bar. The datum head is given to be 2 m. Find the piezometric head. (Assume all Bernoulli’s assumptions, Density of water = 1000 kg/m3, g =9.8 m/s2)...................... 3. Which is the cheapest device for measuring flow / discharge rate. a) Venturimeter b) Pitot tube ¢ None of the mentioned d) Orificemeter 4. Darcy- Weisbach equation gives relation between a) Head loss and pressure loss b) Mass, volume and pressure ¢) Pressure and temperature d) Pressure loss only 5. The principle of Orificemeter is same as that of Venturimeter. a) True b) False 6. What is the relationship between Orificemeter diameter and pipe diameter a) Orificemeter diameter is 0.5 times the pipe diameter b) Orificemeter diameter is one third times the pipe diameter ¢) Orificemeter diameter is one fourth times the pipe diameter d)…
The stream function for a two-dimensional flow is given by v = 2xy. The velocity at (2, 2) is?
Problem 6 (25 minutes) The following rigid beam is supported by a pin and two steel rods (E=29,000 ksi, α=12 106 1/°F) of diameter d = 1.2 in. The load w = H = 3 kip/ft is applied on the beam and the temperature is raised 40 °F. Use G = 2 ft. 1. Draw the expected kinematics of the system 2. Determine the vertical displacement of point D Gift EDO ע G(ft) A Kip W = H (kite) HE RIGID 5 ft B