Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the pressure drop through the network. Pipe 1: D₁ = 450mm, L₁ = 800m Pipe 2: D₂ = 400mm, L₂ = 700m Pipe 3: D3 = 500mm, L₁ = 600m

Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the pressure drop through the network. Pipe 1: D₁ = 450mm, L₁ = 800m Pipe 2: D₂ = 400mm, L₂ = 700m Pipe 3: D3 = 500mm, L₁ = 600m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
Question: In the water network shown in figure,the Hazen-Williams coefficient C for all pipes is 100. a) Using the Hardy Cross method, determine the flow in each pipe to the nearest 20 gprn. b) Find the residual pressures at points B and C, given that the pressure at point Aee is 50 psi. C) If the flow input A is doubled,what would be the residual pressure at C? Elevation 1,600 gpm A A 100 ft B 150 ft C 140 ft 1,500 ft 8 in 500 ft 10 in B 1,000 ft 10 in 1,000 gpm 600 gpm
4.5.4. If the pressure difference between points 1 and 2 in Figure P4.5.4 is 25 psi. What will be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 105 ft/s and neglect minor losses. 10 in dia 2000 ft, 8 in dia A B 1600 ft, 6 in dia Figure P4.5.4 C 800 ft, 10 in dia 2.
Given a three-pipe system, the total pressure drop is PA - PB = 150,000 Pa, and the elevation drop is ZA ZB = 5 m. The pipe data are: Pipe 1 2 3 L, m 100 150 80 A. O 0.00283 m³/s O 0.00146 m³/s The fluid is water (density 1000 kg/m³ and kinematic viscosity 1.02x10-6 m²/s). Calculate the flow rate Q in m³/h through the system. (3 O 0.00675 m³/s O 0.00834 m³/s d, cm 8 6 4 1 €, mm 0.24 0.12 0.20 2 eld 0.003 0.002 0.005 • B
A vertical pipe system shown in the Figure below, d = 300 mm throughout, carries 0.82 (m³/s) of water. Find the pressure drop between A and B if B is 100 m higher than A. Neglect minor losses. Assume f= 0.02, 0.021 and 0.019 for pipes No. (1), (2) and (3) respectivily. I 250 m 550 m 250 m B 11 550 m A 350 m 350 m 550m
Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of depth is -0.004 ft/s. Determine the cross-sectional area of the tank. The total length of the 0.40-in.-diameter pipe is 18 ft, and the friction factor is 0.03. The loss coefficients are: 0.50 for the entrance, 1.5 for each elbow, and 10 for the valve. A = ft² 3 ft BAMIN Valve
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
Example 3: A pipe gradually tapers from 0.6m at A to 0.9m at point B. the elevation difference between A and B is 3m. Find pressure head and pressure at point B if the pressure head at A is 15m and velocity at A is 2m/s. Assume the frictionless flow.
A water pipe gradually changes from 150 mm at a point X to 450 mm at point Y. Point X is 5 m below point Y. Evaluate the pressure difference between X & Y when the flow is 180 L/s. Neglect losses.
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 10-5 ft2/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s². Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. 2 Drag and Drop your answer below. A BI 三三EE II 125 !! ...
1. There is a leak in a horizontal 30 cm pipeline (f= 0.025). Upstream from the leak two gages 600 m apart on the line show pressures difference of 140 kPa. Downstram from the leak two gages 600 m apart show a pressure difference of 126 kPa. How much water is being lost from the pipe? a. 7 L/s b. 9 L/s c. 11 L/s d. 5 L/s 2. A new cast-iron pipe 400 m long and 15 cm in diameter carries 42 L/s of water. Determine the frictional loss of head if f=0.0091 a. 5 m. b. 7 m. c. 8 m. d. 6 m.
A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.