Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In the position shown, a 18.86-kN horizontal force is applied to the bucket at point L. Assuming the weight of the backhoe arm is negligible compared to forces acting on it, find the force acting on pin A (FA) in kN.

Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In the position shown, a 18.86-kN horizontal force is applied to the bucket at point L. Assuming the weight of the backhoe arm is negligible compared to forces acting on it, find the force acting on pin A (FA) in kN.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

An 8-in diameter piston is pushed inside a cylinder having an 8.005in diameter. The gap is filled with a lubricant (v= 0.003 ft²/s, SG = 0.80). If the piston is moving at 0.5 ft/ s, find the frictional resistance when there is an engagement of 10 ft. a. 324.54 Ib b. 227.98 Ib c. 216.78|b d. 236.46 Ib e. 331.12 lb
The figure below shows the stress strain diagram of a cortical bone, with initially rectangular cross section of 15 x 20 mm2, and length of 10 cm. using this figure determine: a) The elastic modulus b) The yield strength c) The ultimate strength. d) The corresponding ultimate true stress, if you know that the instantaneous cross section was at this point was 12 x 17 mm?. e) The deformed length corresponding to the ultimate strength. f) The poison's ratio corresponding to the ultimate strength for the following two cases: a. Use the 15 mm as the undeformed specimen width. b. Use the 20 mm as the undeformed specimen width
Instructions (PART 2): Draw the shear and bending moment diagram of each beam loaded as shown. Show your solution for the shear and moment ordinates. 4.
Formül; TL 2 5 için c = cz =;(1-0,630b/a) M,(!zy .2– ly .y) + M,(1z .z – lzy.y) Tmaks = Gab Czab³G' Мy T M= 300 N -m B = 60° 2tA Iz.ly – Izy² Ox + Oy Ox – Gy 21xy Ox + Øy tan28, - cos20 + Txysin20 , Jort = O- dy •B Iz + 0y ) + 16 mm Ty'y' = sin20 + Trycos20 , omaks.min = 16 mm D -40 mm--40 mm→| Tmaks = +: An M pair of forces is applied to the beam shown in cross-section in a plane that makes vertical B vaccination. Find the stress at point A. O -3,37 MPa O 3,37 MPa O -4,87 MPa O 5,86 MPa O -5,86 MPa
Plz, solve this problem properly with detail?, it is not graded question. Four digits of reg.no : 5395
M-(Izy.2-ly.y)+ M,(1z.2 – Izy.y) Iz.ly - Izy Pr My Formüller; o -- t Pr Oz + Øy Gort Tmaks 2t 2 2 2 Oz + dy + Tc d?y M(x) Omaks.min + Ty, E= aAT, T = 2 2 I dx? El MalanıcpXc, @pjc Malanıpc El Tmaks = EI ƏM 1²EI VQ EI M dx. Per It Both ends of the fixed (fixed) rod were mounted at 0 °c. Calculate the minimum diameter of the bar so that there is no buckling in the bar when the ambient temperature rises to 100 °C? a= 12.10-6/°C, L= 5 m 13,069 cm 10,024 cm 15,034 cm 18,038 cm 11.026 cm
Calculate the worst-case wall thickness between datum feature B and the 2-inch inside diameter in the drawing below: 04.00 .250 .480 .240 O .500 O .245 Ø2.500-2.540 0.000DA B Ø2.000-2.010 0.010DABL A
H.W.1 Honda CR-V is a midsize SUV car with m= 1550 kg, l= 2620mm Assume a, = az, h= 720mm, Hy= 0.8 determine the maximum acceleration of the car and minimum time for 0-100 km/h if a) the car is rear-wheel drive. b) the car is front-wheel drive. c) the car is four-wheel drive. H.W.2 RoadRazer is a light weight rear-wheel drive sportscar with m = 300 kg, 1 = 2286 mm, h = 260 mm Assume a, = az. If the car can reach the speed 0- 100km/h in t= 3,2 s, what would be the minimum friction coefficient?
Find the cost of the pumping water: Cost= r*P. where r 0.3353 is the interest rate and Pis the absolute pressure )( kpa) in the pipe Water Air 60 cm 50'cm 40 cm 50 cm S-0.8 S-0.5 45 deg Select one a. 172.7898 b. 34.5580 c. 138.2319 d. 69.1159 e 103 6739
Marker Tools Presenter Info | Resources 1.4. Ngẫu lực - Bài tập 2: a) Tỉnh Mômen của lực F tại O và B b) Tính Mômen của lực P tại O và A 2m A 1m 3m 30° y F=10N 60° P=20N4 4m m X
Q2 Q1 u (poise) Sp. Gr. D (mm) L (m) Q3 Q (Lit/s) H E (mm) 0.02 0.8 50 500 0.19 18 2
A hydraulic lift has a maximum fluid pressure of 500 kPa. What should the piston cylinder diameter be to lift a mass of 850 kg. what is the answer? incluide diagram. a. 0.0017 m^2 b. 1.7m^2 c. 0.017 m^2 d. 16.677 m^2