Please answer as soon as possible, thank you. The slide in a pipe is to be opened and closed. Actuation is to be triggered by meansof a valve with selector switch. A double-acting cylinder Is to be used as the drive.• The slide is to open/close only gradually since the load on the pipe wouldotherwise, be to great (the formation of surges is to be avoided).1. Design the pneumatic circuit diagram.2. Carry out the assembly.3. Check the assembled circuit.4. Describe the mode of operation of the circuit.5. Compile an equipment list6. Observe the pressure ratios upstream and downstream of the flow control valveand document these.Wastewater treatment1. If the selector switch is actuated, the cylinder is to advance and open up flow.2. If the selector switch is reset, the cylinder is to return into the initial position andthe slide is to close.

Solution: The Pneumatic circuit diagram is shown below:

The slide in a pipe is to be opened and closed. Actuation is to be triggered by means of a valve with selector switch. A double-acting cylinder is to be used as the drive. • The slide is to open/close only gradually since the load on the pipe would otherwise, be to great (the formation of surges is to be avoided). 1. Design the pneumatic circuit diagram.

The slide in a pipe is to be opened and closed. Actuation is to be triggered by means of a valve with selector switch. A double-acting cylinder is to be used as the drive. • The slide is to open/close only gradually since the load on the pipe would otherwise, be to great (the formation of surges is to be avoided). 1. Design the pneumatic circuit diagram.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In hydraulic and pneumatic circuit designs, certain steps are required that must be followed sequentially, order these steps in the correct order; 6.- Power generation sources. 1.- Determine the necessary functions and requirements to be met. 4.- Actuator control system. 2.- Determine the form of connection between the cylinders and the valves. 5.- Sequence of movements and signal transmission. 3.- Components required to perform the functions. O 1, 2, 4, 3, 6, 5. O 3, 4, 5, 6, 1, 2. O 1, 3, 4, 2, 6, 5. O 6, 4, 3, 5, 1, 2.
Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation system of a small aircraft. The hydraulic system uses a variable engine driven pump as power supply. The pump takes flow from a reservoir. The circuit is protected against overload by a pressure relief valve. The speed and the direction of rotation of the flap motor are controlled using an electrically operated proportional valve. The aileron actuator contains a double acting cylinder, which is also controlled by an electrically operated proportional valve. Draw the circuit using ISO standard! Use the following symbol for the electrically operated proportional valve THEL
Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation system of a small aircraft. The hydraulic system uses a variable engine driven pump as power supply. The pump takes flow from a reservoir. The circuit is protected against overload by a pressure relief valve. The speed and the direction of rotation of the flap motor are controlled using an electrically operated proportional valve. The aileron actuator contains a double acting cylinder, which is also controlled by an electrically operated proportional valve. Draw the circuit using ISO standard! Use the following symbol for the electrically operated proportional valve JIHEL
Circuit Problem and Description: Using the given components, design a pneumatic circuit which will correctly and safely operate this machine control application. This is a simple two- cylinder sequence (A and B), as follow; A+ B+ A- B-. This is known as a simple sequence when the order for the cylinder to move out is the same as for cylinder to move back. The start-up signal will be by means of a normally closed 3/2 way valve operated by push button (M1) or normally closed 3/2 way valve operated by switch (M2). Full extension and retraction of each cylinder can be monitored by four normally closed 3/2 way valve operated by roller (M3-M6). Extension and retraction speeds of both cylinders must be adjustable using 2 sets of 2 single-direction flow regulation valves. Materials: Component Description Part # SAI 2026 Double acting cylinder SAI 2015 Normally closed 3/2 way valve operated by push button SAI 2016 Normally closed 3/2 way valve operated by switch SAI 2013 Normally closed 3/2 way…
Circuit Problem and Description: Using the given components, design a pneumatic circuit which will operate a double acting cylinder (A) from any one of two identical valves. The double acting cylinder will move out when either push button (M1) or (M2) is pressed, or when they are pressed at the same time. When the buttons are released, the cylinder will return to the initial position. Materials: Part # Component Description Quantity SAI 2026 Double acting cylinder SAI 2015 Normally closed 3/2 way valves operated by push button SAI 2023 Pneumatically piloted 5/2 way monostable valve SAI 2007 2 1 "OR" logic function valve 1 Teske Circuit Problem and Description: Using the given components, design a pneumatic circuit which will correctly and safely operate this machine control application. WWith this circuit, it must be possible to regulate the delay of a double acting cylinder (A). The cylinder will be driven by a valve, actuated by two pneumatic push buttons. One of the two push buttons…
It is desired to operate the pneumatic cylinder below which has to pistons A and B to stamp the die D. The piston A s returned in its back stroke by a spring, and has quick return .It is advised to use solenoid and pilot valves DCV . ( best design is to use two DCV valves ) 1- Make a complete circuit layout to operate the device above, using the appropriate symbols.2-Describe in details how your system works ( typed ) 3- Names the components of your system. 4- Any pneumatic working design will be considered as correct.
Read and understand the problem then draw a pneumatic circuit diagram for it. Include complete port and component designation on your circuit diagram. No need to follow the time given in the problem, just make the forward and return stroke speed adjustable. A double-acting cylinder (1A) guides cylinder pins towards a measuring device. The pins are separated by means of a continuous to and fro movement. The oscillating motion can be started by means of a valve with selector switch. The duration of the forward stroke of the cylinder is to be tl = 0.6 seconds, the return stroke t3 = 0.4 seconds. The cylinder is to remain in the forward end position for t2 = 1.0 seconds, resulting in a cycle time of t4 = 2.0 seconds. Messfix 1A
Design the circuit (pneumatic/hydraulic/electro-pneumatic/electro-hydraulic) for the following problems:1.A double acting cylinder of pneumatic system will extend when two pushbuttons are pressed. The retraction is doneautomatically when either one of the pushbuttons is released.2A pushbutton is required to extend a cylinder of a pneumatic stamping machine. Once the cylinder at the full extensionposition, it will wait for 5 seconds before it is automatically retracted.3.The cylinder extends when two pushbuttons are pressed. The cylinder retracts when the set pressure of 5 bar is achieved.4.Given a hydraulic system with double acting cylinder. The cylinder extends when the lever is triggered. The retraction of thecylinder is achieved by another lever.
(b) The schematic diagram of Assembly fixture for greasing of roller bearings is shown in Figure 4. After assembling individual roller bearing parts, roller bearings are to be pressed by a pneumatic cylinder A. Cylinder B is required to operate a grease press twice for injecting grease into the roller bearing. Develop an electro- pneumatic control circuit for this system. Ciamping oyinder Assembled bearings Pressing cylinder Grease box Figure 4
For the pneumatic circuit in the figure, name each of the components and describe their operation (what each action does).
5. Mark the correct statement for Flight computer architecture. a. Neither the ELACS nor the SECS provide the only control to either the pitch or the roll axis. b. Both ELACS and SECS provide the control to pitch and Yaw Axis. c. Both ELAC and SECS Have full control or Pitch and Roll Аxis. 6. To increase the redundancy and safety the power supplies to individual control surfaces (Actuators/Motors) are signaled by a. Different lanes but same hydraulic system. b. Same lane and Different hydraulic system. c. Different lane and Different hydraulic system. 7. Communication between the FBW system computers is done via a. ARINC 429 data bus. b. Normal twisted wire cables. c. No communication happens. 8. The ELACS control the aircraft in pitch and they do so by sending commands to the left and right elevators and also by sending longer term trim commands to the "Trimmable Horizontal Stabilizer". Which law is this a. Direct Law b. Normal Law c. ELACS never control Horizontal Stabilizers, No Law…
Bending Tool Problem: Sheet metal is to be bended on a pneumatically actuated bending rig. After it has been clamped the piece is initially bent by a double-acting cylinder A and subsequently bent into the finished form by cylinder B. The sequence is initiated manually by a push button. The circuit must be so constructed that each time a start signal is given a full cycle is completed. Draw the pneumatic circuit diagram of the given problem Positional Sketch: