The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.

The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
QUESTION 1 Two magnetically-connected circuits have the following characteristics: . A series-opposing connection of coils (dot convention). The primary side is connected to a voltage source that has a magnitude of 230 V and a phase angle of 45 degrees. . The primary-side inductive reactance is jXL1 - j8 Ohm. . The secondary side is connected to a resistive load of 10 Ohm. . The secondary side inductive reactance is jXL1 =j5 Ohm. . The mutual inductive reactance is jM=j1 Ohm. The magnitude of the voltage across the resistive load is:
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
Combination circuit what is PT? RT? IT? Voltage Across each load?
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
WHAT IS THE POSSIBLE OBSERVATION AND CONCLUSION ABOUT SERIES–PARALLEL CIRCUIT AND DELTA WYE CONVERSION?
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?