The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. The normal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameter of the spacer.

The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. The normal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameter of the spacer.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Related questions

Q: 3) Determine the moment of inertia of the composite area about the x and y axes 6 in.- T 3 in. + 3…

A: find the moment of inertia about x and y axes.

Q: According to the figure, the vector equation is x B A vB=vA+vA/B O Option 4 OVA/B=VA-VB VA= vB+vA/B

Q: 20-teeth sprocket driving a 100 teeth sprocket with a center distance of 38 pitches. Find the chain…

Q: Member AB has the angular velocity, WAB. 3.5 rad/s and angular acceleration, a AB. 7 rad/s².…

Q: A jet of water from a fixed nozzle has a diameter d of 30 mm and strikes a flat plate at angle u of…

A: Diameter of a jet, d=30 mm=0.03 mAngle between the direction of flow and normal to the plate,…

Q: 2. Determine the slope and deflection at point B of the beam AB shown using the Area- Moment Method.…

A: Given beam

Q: A Brayton cycle is used to produce power. Air flowing at 40 lbm/s enters the compressor at one…

Q: Four people work

A: Number of people(P)=4 time(t)=6 hr temprature=15oF Q=P*t*h heat(h) equivalent of occupancy for room…

Q: Q.6 A vapor compression cycle uses R134a as the refrigerant. The vapor condenses at 40°C and is…

Q: A Brayton cycle is used to produce power. Air flowing at 40 lbm/s enters the compressor at one…

Q: The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only…

Q: A rigid container is closed at one end and measures 8 in. diameter by 12 in. long. The container is…

Q: A 5 ton refrigeration system operates on a vapor-compression refrigeration cycle with…

Q: Given the top view and right side view, draw the sectional view of the figure. Please include the…

A: Find Sectional View of the given figure

Q: A body moves such that its acceleration is given by a = 2 + 12t where t is in seconds and ‘ a’ is in…

Q: Topic: Centroid Graph and compute the center of mass/ centroid of the region R = {(x, y): 1 ≤ x ≤…

Q: 3. Draw the shear-force and bending-moment diagrams for the beam shown. Determine the maximum shear…

Q: 3) What are the requirements for an efficient steam condenser 71

Q: In this diagram, which pressure differential valve has pressure loss? Which part of the system has…

A: Differential valves are used for detecting differential pressure. detection of the valve failure of…

Q: Q1/Evaluate the integral -2x 2 e √₁--4x 1ế S dx

A: evaluate the integral.

Q: The forces F1 = 2.50 kN and F2 = 3.20 kN are parallel to the z and x axes respectively. Determine…

A: given data F1 =2.50kN F2 = 3.20 kN find the minimum tension in cable AB.

Q: Q.2 The heat absorption and rejection temperatures of a Carnot refrigeration cycle are -8°C and 55°C…

Q: Derive the equation of power transmitted by Flat-belt between two pulleys then find the equation of…

Q: Q/: Replace the 900N force of figure shown below by (1) a force through A and a couple (2) a force…

A: For the given system To determine (a) replace 900 N force by a force through A and a couple (b)…

Q: Derive the expressions for V and M for the beam shown, and draw the shear force and bending moment…

Q: 1002/ A timber beam is reinforced with Steel Plates rigidly attached at the top and bottom as shown…

Q: What is the work done by the compressor in KJ/kg?

A: To find Work done by the compressor in KJ/kg

Q: Q1. Determine the distance x measured from the y axis to the centroid of the area of the triangle…

Q: Figure 1 shows water at 20°C to be circulated from and to the reservoir. The 30 mm diameter pipe…

Q: An air-conditioner with refrigerant-134a as the working fluid is used to keep a lab at 26°C by…

A: Given DataP1=500kPaP2=1200kPaP=850kWQ=100L/minT1=34°CT2=34°C

Q: A flat plate, manufactured from Perspex, is drawn submerged through 25°C still water at a velocity…

Q: ᴛʜᴇ ᴘᴇɴꜱᴛᴏᴄᴋ ᴏꜰ ʜʏᴅʀᴏᴇʟᴇᴄᴛʀɪᴄ ᴛᴜʀʙɪɴᴇ ɪꜱ 0.5ᴍ x 0.5ᴍ ᴡɪᴛʜ ᴠᴇʟᴏᴄɪᴛʏ ᴏꜰ 5.5ᴍ/ꜱ ᴀɴᴅ ʜᴇᴀᴅ ᴏꜰ 20ᴍ. ᴡʜᴀᴛ…

A: Area, A= 0.5×0.5= 0.25 m2 Velocity, V= 5.5 m/s Head, H= 20 m Turbine efficiency, η= 92%= 0.92…

Q: The steel tie-bar shown in the figure has been designed to carry a tension force of 83 kN when…

Q: 3. Is there a difference between the values of the water jet force on plate (F₁) and the force…

A: Yes , there is a difference between jet force and force due to weight.

Q: For the following mechanical systems, obtain the equations of motion in Laplace domain.

Q: Considering that the change in enthalpy at the first stage of a Reheat Rankine Cycle is 450 BTU/lb…

Q: B) What are the requirements for an efficient steam condenser A -- 1.

A: Requirements of efficient steam condenser: 1) To reduce the steam turbine exhaust pressure so that…

Q: Calculate the wire diameter of a helical spring using Wahl's factor if the load applied is 130 lb…

A: Given:P=130 lbKs=8ζmax=50 ksi

Q: Consider the two-degrees-of-freedom mass-spring system below. Assume m₁ = 30 kg, m2 = 35 kg. If the…

Q: Figure 2 shows an electrical motor with mass M=13 kg located at the middle of pinned-pinned beam. A…

Q: For an ideal cold air-standard Brayton cycle with a compressor inlet temperature of 300 K and a…

A: In case of brayton cycle, optimum pressure ratio is the pressure ratio where net work done will be…

Q: Consider the system in the figure below, which is pivoted at point O. Assume that a = 0.4 m, b = 1…

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: ᴛʜᴇ ꜰʟᴏᴡ ᴏꜰ ᴀ ʀɪᴠᴇʀ ɪꜱ 35ᴍ3/ꜱ ᴀɴᴅ ᴘʀᴏᴅᴜᴄᴇꜱ ᴀ ᴛᴏᴛᴀʟ ʙʀᴀᴋᴇ ᴘᴏᴡᴇʀ ᴏꜰ 6ᴍᴡ. ɪꜰ ɪᴛ ɪꜱ ᴘʀᴏᴘᴏꜱᴇᴅ ᴛᴏ ɪɴꜱᴛᴀʟʟ…

Q: The difference in elevation between the source of the water supply and the centerline of the base…

Q: Water flow at a 250mm diameter horizontal pipe. The friction factor is 0.023. If the pressure at the…

Q: 1. (True / False) Stress components are opposite in direction on the two surfaces of an imaginary…

Q: The circular shaft AB consists of a 22.9 mm diameter solid steel cylinder in which a 11.8 mm…

Q: 2. A cascade refrigeration system using R - 22 in the low - temperature circuit and ammonia (R-717)…

Q: bi h1 в ки E 4 kN/m 2m Im B с 7777 62 3m x Find: 1- The Distance (a) at which the Beneling moment in…

Question

The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. The
normal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameter
of the spacer.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. 2.1 Determine the tensile stress in each rod. 2.2 Determine the shear stress in pin A between the members. 2.3 If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint
The rectangular piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 16.4 MPa for compression. Round off the final answer to three decimal places.
The collar bearing shown is subject to a 500 kN force. 500 kN The collar is 25 mm thick. Find d and D (to the nearest mm) so that the allowable normal stress in the column collar bearing of o = 280 MPa, the allowable shear stress in the collar collar of t = 200 MPa and the allowable bearing stress between the collar and the support of ob = 70 MPa is not exceeded.
A force of 120 lb is applied to the edge of the member shown in the figure below. Neglect the weight of the member and determine the state of stress at points B and C using the superposition. 120 lb 4.5 in. | 4.5 in. -2.5 in 2.5 in B-
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁ = 30 mm, d2 = 50 mm, and P = 50 kN. P 0.9 m 125 kN 125 KN B 1.2 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is MPa.
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lh and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G
2. Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin. Rod (1) Rod (2) Pin
The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of the rectangular bar is 90 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support - bracket
1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
A flanged bolt coupling connects shafts on each side. It consists of 8- 19 mm diameter bolts on a bolt circle of 300 mm and 6 – 12 mm diameter bolt on a bolt circle of 230 mm. Determine the stress on BOLT CIRCLE land the stress on BOLT CIRCLE 2 (in MPa) due to a torque of 20 KN-m. (in MPa)