The figure shown has trusses 6m apart with midpoint sag rods and Purtins C150x12.5 spaced 2.5m on center. The roof truss is inclined 1 vertical to 2 horizontal. The weight of roofing materials is 0.9 kPa (includes self wt.), wind load is 0.8 kPa perpendicular to the roof surface, minimum roof live load is 0.6 kPa. Consider the roofing to provide full lateral support of the purtins. Fy=345 mPa. Use the NSCP 2015 specifications.

The figure shown has trusses 6m apart with midpoint sag rods and Purtins C150x12.5 spaced 2.5m on center. The roof truss is inclined 1 vertical to 2 horizontal. The weight of roofing materials is 0.9 kPa (includes self wt.), wind load is 0.8 kPa perpendicular to the roof surface, minimum roof live load is 0.6 kPa. Consider the roofing to provide full lateral support of the purtins. Fy=345 mPa. Use the NSCP 2015 specifications.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.1P

See similar textbooks

Similar questions

Which of the following best gives the purlin load wuy? See loaded purlin. The figure shown has trusses 6m apart with midpoint sag rods and Purlins C150x12.5 spaced 2.5m on center. The roof truss is inclined 1 vertical to 2 horizontal. The weight of roofing materials is 0.9 kPa (includes self wt.), wind load is 0.8 kPa perpendicular to the roof surface, minimum roof live load is 0.6 kPa. Consider the roofing to provide full lateral support of the purlins. Fy = 345 mPa. Use the NSCP 2015 specifications. 2. 5m 2.5m 2. 5m roofing TRUSS TOP CHORD Wuy, Truss Spacing = 6m Wux 1 Purlins C150x12.5 Purlin Load Wt kN/m mm^2 mm C150x12.5 0.12 11400 12.7 152 5.1 d tw by SECTION Ix Sx rx ly sy Zy ry Zx mm mm mm^4 mm^3 mm mm^4 mm^3 mm mm^3 mm^3 mm mm 48 8.7 143 1100 112 48.4 378 65.2 1230 574 O 4.35 kN/m 5.56 kN/m O 25.02 kN.m
ASSIGNMENT #6 CASE 2 Purlin Design The figure shown has trusses 5.5m apart with midpoint sag rods and Purlins spaced 2.5m on center. The roof truss is inclined 1 vertical to 2 horizontal. The weight of roofing materials is 0.8 kPa, wind load is 0.7 kPa perpendicular to the roof surface, minimum roof live load is 0.6 kPa. Design a channel section of steel Fy = 345 mPa, for the purlins. Use LRFD and ASD of NSCP 2015.
Figure 1.5 m E -2 m- 3 kN D B -2 m 1 of 1 Identify the zero-force members in the truss. Check all that apply. BE DE CD AB AE BD BC Submit Drouido Foodbook Request Answer
Example 3.15 FIGURE 3.32 Fink trusses spaced at 20 feet on centers support W6 x 12 purlins, as shown in Figure 3.32a. The purlins are supported at their midpoints by sag rods. Use A36 steel and design the sag rods and the tie rod at the ridge for the following service loads. Metal deck: Built-up roof: Snow: Purlin weight: 46.6' 2 @ 12' = 24' 4.679 k 46.6 18.17k (b) 2 psf 5 psf 45 18 psf of horizontal projection of the roof surface 12 pounds per foot (lb/ft) of length 112 42' 90' (a) P P 2@ 12' = 24' F R R 12 (c) 45 3' 3' 3' 3' 12' 4.679 k 4.679k
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
The largest load P that can be applied is approximately equals: Arca - 0.00126 m oall - 45 MPa a)57 kN B Aren- 0.0007 m b)60 kN Weld allowable strength - 60 kN all - 95 MPa c)67 kN d)50 kN
The following diagram shows a partial floor framing plan of an elevated walkway building connecting an airport terminal building to the adjacent garage. The concrete floor is not post- tensioned. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Framing members are not exposed to weather or in contact with soil. Use ASCE Table 4.1 to determine the design live load for this floor. 30-0¹ S Colm- Ö 90-0 - Mark 54 59 25 30-0¹ N BI -Sinder ASCE 7-10 Chapter 4 Live Load.pdf 50 psf 60 psf 100 psf 150 psf 2
2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier, the allowable stresses for the material are t = 15 ksi and o, = 32 ksi. What is the allowable load of the connection? L4 x 3-1/2 W18 × 86 W24 x 117 Girder Beam
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN