The distance between the horizontal supports of a transmission line is 114 meters. The Cross-sectional area of the conductor is 2.225 sq cm. is Calculate the factor of safety, subject to the following conditions. (1) Wind pressure = 1.5 kg/m run. (2) Breaking stress = 2540 kg/sq – cm. (3) Weight of carrier = 1.125 kg/m. ( 4 ) Seg = 3.92m.

The distance between the horizontal supports of a transmission line is 114 meters. The Cross-sectional area of the conductor is 2.225 sq cm. is Calculate the factor of safety, subject to the following conditions. (1) Wind pressure = 1.5 kg/m run. (2) Breaking stress = 2540 kg/sq – cm. (3) Weight of carrier = 1.125 kg/m. ( 4 ) Seg = 3.92m.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.17P: Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All...

See similar textbooks

Similar questions

An over head transmission line supported from two towers location at the same level. The distance between the towers is 200 m. The tension in the wires is 9000 N. The weight of one meter of the conductor is 10 N. The sag of the wires is * 2.55 m 1.55 m 4.55 m 5.55 m Non of them
An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
Problem #1 • An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please
A single-conductor belted cable of 5 km long has a conductor diameter of 2 cm and an inside diameter of lead sheath of 5 cm. The cable is used at 24.9 kV line-to-neutral voltage and 60 Hz frequency. Calculate the following: a. Maximum and minimum values of electric stress. b. Optimum value of conductor radius that results in smallest (minimum) value of maximum stress.
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
The number of disc insulators used in a suspension insulator setup with string efficiency 90 %, phase voltage 33 kV, and the voltage across insulator nearest to conductor 9 kV is . Calculate the weight due to ice on a transmission line where the Total weight of conductor = 3.2 Kg/m, actual weight of conductor = 1.6 Kg/m, and weight due to wind = 0.4 Kg/m.
(a) A three phase transposed transmission tower comprises of three-bundled conductor and double-circuit configured in vertical position as shown in Figure 2. Each sub-conductor in each circuit and each phase is an ACSR type, size 477,000 cmil and stranding 26/7. Given the GMR of each sub-conductor is 0.8809 cm and diameter is 2.1793 cm, analyze: i. Inductance in mH/km ii. Capacitance in µF/km 0.75m 7.5m b' 4m 4m 45cm Figure 2
(ii) An overhead transmission line is supported at a river crossing by two towers of height 37 m. The weight of the conductor is 0.307 kg/m. The weight due to wind is 1.3 kg/m. The ultimate strength is 1200 kg and factor of safety is 3. If the Span length is 150 m. Determine (a) Total weight of the conductor (b) Sag (c) Total Length of conductor between supports (d) Clearance between the lowest point on the conductor and water level.
a.Why does power plants have high amounts of voltages? Explain. b.Is it safe for transmission lines to have high current instead of high voltage? Why? c.What phenomenon is avoided by having separations between three conductor phases? Explain this phenomenon.
The towers of height 45 m and 85 m respectively support a transmission line conductor at water crossing. The horizontal distance between the towers is 550m. If the tension in the conductor is 1550 kg, Weight of conductor is 1·65 kg/m. Bases of the towers can be considered to be at water level. Estimate: i. distance between lowest point on conductor and each tower ii. sag at each tower iii. the minimum clearance between ground and conductor
A 84 meter long conductor with a unit weight of q=(0.8) kg/m is separated from each other.It is stretched on two poles in a straight span at a horizontal distance of "a" and the deflection valuef=16 meters measured. Accordingly, with the catenary method: a. Calculate the value of "a" b. Horizontal 18 meters from the lowest point of the conductor to any pole Calculate the deflection value at distance. c. Calculate the resultant tension force (S) at the peaks. D. At the apex, this is the angle that the direction of the S force makes with the horizontal axis calculate.