The data given for a vertical sagcurve on a roadway plan andprofile sheet are as follows: PVIstation @ 32+11.61, PVI elevation =54.18 ft, back tangent gradient g1 =- 4.00 percent, forward tangentgradient g2 = + 7.00 percent, andlength of curve L= 600ft. Determinethe curve elevations at half-station intervals along the curve,and compute the station andelevation of the lowest point. PLEASE PROVIDE COMPLETE AND COMPREHENSIVE SOLUTION AND FINAL ANSWER ASAP

The data given for a vertical sagcurve on a roadway plan andprofile sheet are as follows: PVIstation @ 32+11.61, PVI elevation =54.18 ft, back tangent gradient g1 =- 4.00 percent, forward tangentgradient g2 = + 7.00 percent, andlength of curve L= 600ft. Determinethe curve elevations at half-station intervals along the curve,and compute the station andelevation of the lowest point. PLEASE PROVIDE COMPLETE AND COMPREHENSIVE SOLUTION AND FINAL ANSWER ASAP

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter14: Highway Surveys And Location

Section: Chapter Questions

Problem 17P: The following table shows the stations and ordinates for a mass diagram. The free-haul distance is...

See similar textbooks

Similar questions

Assignment 3: Vertical Curve Design Question 2 The reduced level at the intersection of a rising gradient of P % and a falling gradient of Q % on a proposed road is XX.XX m. Given that K value is KK. The throught chainage of the intersection point is YYYY.YY m and proposed vertical curve is to have equal tangent. As a civil engineering you are required to prepare the following vertical curve design calculations: a) The through chainage of the points of the vertical curve if the minimum required length is to be used (Lv) and the vertical curve setting out data at 20 metres interval. b) The chainage and reduced level of the highest point on the curve. c) Through chainage at highest point was located exactly under a bridge, if the RL of soffit is SS.SS m, calculate the headroom based on proposed vertical curve design.
The following table shows the stations and ordinates for a mass diagram. The free-haul distance is 600 ft. Overhaul cost is $12 per station yard. (a) Use the method of moments to compute the additional cost that must be paid to the contractor. (b) Sketch the ground profile if the finished grade of this roadway section is level (0 percent).
A-1.10% grade meets a +0.60% grade at station 36+00 and elevation 800.00 ft. The +0.60 grade then joins a +2.40 grade at station 39+00. Part A Determine the elevation at the low point of the curve. Express your answer in feet to six significant figures. Elev = Submit Part B VAΣo↓ vec Request Answer Determine the station at the low point of the curve. Submit O 38+42.763 O 35+40.763 O 36+42.763 O 36+44.763 Request Answer ? ft
A 500-ft curve, grades of g₁ = +2.00% and g2 = -2.50%, VPI at station 96+80, and elevation 845.260 ft, stakeout at full stations. Part A Determine the elevation at the high point of the curve. Express your answer in feet to six significant figures. Elev = Submit Part B AΣo↓ vec Request Answer Determine the station at the high point of the curve. O 97+12.77 O 96+13.33 O 96+52.22 O 97+96.66 ? ft
1. What are the extra clearances provided on a curved track? Describe the extra clearances provided between two adjacent curved tracks. 2. Establish a relationship between the radius and versine of a curve. How is the degree of a curve determined in the field? 3. Enumerate the various methods of setting out a circular curve. Describe the tangential offset method for laying a circular curve. 4. Which among the future railroads development are you most looking forward?
Imagine a two lane highway segment with crown slopes of -1.5% and the start of the tangent runout at St.Km.0+000.00.The design speed is 75 km/hr. The Radius of the circular curve is 408 m.Prepare a small superelevation table showing superelevations of each travel laneatthe startand endof the tangent runout,at the start and end of the superelevation runoffand at the point of curvature only. Notes: Make sure emax< 0.08, take Sr 1/200. Use Turkish Practice
. A+4.5% grade on rural free way intersects with a-2.5% grade at chainage of 67+500 at an elevation 75.00. If the design speed of free way us 100km/hr. N.b obtain the value of (k) from the following table # determine the chainage and elevation of the Bvc, Evc and the lowest point #if the road is stacked at 50m interval, calculate the elevations of all full chainage a long the curve. Table. minimum value of k for vertical curve. Design speed crest value sag value 40 6 8 50 11 12 60 16 16 70 23 20 80 33 25 90 46 31 100 60 36 110 81 43 120 110 52 130 133 57
Compute the cross sectional area for the roadway section at station 10+33.89 using the following cross section data. The width of the roadway is 50 feet. -25 25 25 25 F 11.8 -42.5 F 14.3 -32.0 F 15.8 F 16.3 65.4
The tangent vertical alignment of a section of proposed highway is shown in the figure below. Determine the vertical clearance (ft) between bridge structure at Station 23+00 and the vertical curve.
A section of road has an entry grade of -8,43% and an exit grade of -4,96%. Determinethe minimum vertical curve length (use K,L, A) and the stopping sight distance for the worst-case scenario. The design speed of the road is 80km/hr. Attach or type all workings.
DRG PreAns ns of Int no 300 ÷ Rec Intg PM Fri Feb 17 88 a 9 LCM ● ● 3.1 Handout STApvc and Epvc Xhigh and yhigh Solution: 1) Determine Lmin Example 2: A crest vertical curve joining a +3% grade and a -2% grade is to be designed for a two-lane highway with a design speed of 60 mph. If the tangents intersect at station (187+40.00) at an elevation of 180 ft., use the K-value to find the length of curve and determine the stations and elevations of the PVC. Also, find the location of the high point. Give: u-60 mph; G₁=+3.0 % %; G2=-2.0%; STAPVI = 187+40.00; EPVI =180 ft. Find: ☆ 3.1 Handout ✓ Design Speed (mi/h) 15 20 25 30 35 40 45 50 55 60 a. Lmin = KA 151 X5 755 i. K= 151 65 70 75 80 Table 3.2 Values of K for Crest Vertical Curves Based on Stopping Sight Distance Rate of Vertical Curvature, K X T 80 115 155 Stopping Sight Distance (ft) 200 250 305 360 425 495 570 645 730 820 910 Calculated 3.0 6.1 11.1 18.5 29.0 43.1 60.1 83.7 3.1 113.5 150.6 192.8 246.9 311.6 383.7 Design 3 7 12 19 29…
Read the question carefully and give me right solution according to the question. Station 10+00.00 has an elevation of 110.00 and a grade of -3%. Station 20+00.00 has an elevation of 105.00 and a grade of +2%. What is the stationing at the two grade intersections? options A) 14+00, B) 15+00, C) 16+00, D) 17+00)