=The converter in the next figure has load resistance, R =U.75 2; input voltage Vs = 240 V; and battery voltage, E =12 V. The average load current, Ia 180 A, and thechopping frequency is f = 220 Hz (T = 4.5 ms). Use theaverage output voltage to calculate the value of loadinductance L, which would limit the maximum load ripplecurrent to 5% of Ia.°+VsChopperSWt=0+Vo DmE

Here, the converter configuration given is Buck converter and according to the condition, putting…

Answered: = The converter in the next figure has…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Calculate the rms value of the output voltage of an AC-AC converter with the following specifications. Vs—110*sqrt(2)*sin(wt), Alpha Pi/6
In the given circuit, a step down transformer with an RMS voltage as 110V /11-0-11 V is used with RL = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. D, CT Vin RL D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. all
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
3. Two circuit elements in series consume 60 VAR when connected to a 120 – V, 60 – Hz source. If the reactive factor is 0.6, what are the two components and what are their values?
For the following circuit if the secondary voltage of the transformer is 20V rms, the output voltage and the PIV of the diodes are V. 2 Vm C3 D, D2 D3 A D4 C2 C4 + 2Vm 2Vm O 130.1 V, 55 V O 113.1 V, 56.56 V 123.2, 61.61 V 55.5 V, 33 V
A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.
For the following circuit if the secondary voltage of the transformer is 20V rms, the PIV of the diodes are ZV +1H +1 C3 D₂ D₁ 000 000000000 + C₁ O 55 V O 61.61 V 33 V O56.56 V C₂ HE 2V + m D3 + Ca H 2V
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
Determine the maximum peak-to-peak ripple current of previous problem by using the next equations, and compare the results. DI. = max V R tanh R 4fL DI = V S max 4fL
Does the input power factor of convertors depend on the load power factor? why?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS