The cantilevered beam shown below has a solid 1mm * 1mm cross-section. Find the beam elongation if the material is Lead?

Q: Consider water flow through a pipe 6 m long and internal diameter 300 mm. The head loss due to…

A: Length of pipeL=6mDiameter of pipeD=300mm=0.3mhead loss due to frictionhf=6mValue of surface…

Q: There are expanded 0.90 kg/s of steam at constant pressure from 30 bar and 70% quality to a final…

A:

Q: Steam at 350 °C flows through the stainless steel pipe with k=26 W/m.°C. The inner and outer…

A:

Q: ED.indd 1. Approved eye protection A. is not required for the lathe. B. should always be worn when…

A: Explanation: 7) Inspect the cutting tools before use for damage and wear otherwise; The improper…

Q: Problem 20-7 A pair of worm and worm wheel is designated as (2/40/10/4). The input power to the worm…

A: The input power is P= 5 kW The rotational speed is N=720 rpm The pressure angle is φ=20° The number…

Q: The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm…

A: As per guidelines only first three questions be answered. The area under the turning moment diagram…

Q: 1. Start from the following equations from class notes (treat as given): The shear stress in pipe…

A:

Q: →Compare (100) and (111) surfaces in FCC. Which one should have a lower surface energy?

A: To compare: The (100) and (111) surfaces. Concept used: (100) surface: The fcc metal is cut parallel…

Q: (a) Assume that in each fission of 235U, 200 MeV is released. Assuming that 5% of the energy is…

A: Dear Student, As you have posted two different questions but as per Q & A guidelines I will…

Q: A vertical dam on a large lake is 30 ft tall and 60 ft wide, and the water level is 3 ft below the…

A: Given Data The length of the lake is: L=30 ft The width of the lake is: w=60 ft The water level is 3…

Q: The simply supported beam shown in Figure 1 (see next slide) spans a distance of L = 6 m and carries…

A: Given data: L=6 mma=1.5 mb=30 mmd=240 mmt=9.5 mmd=240 mmThe modulie of elasticityof wood planks is…

Q: If possible please draw figure. [Answer must Be in Handwritten Format Only] A tank of water (SG=1.0)…

A: GivenS.G=1h=5mw=3mx=2m

Q: Find solutions for the divergence and curl of the vector field y at (1, 0, -1). v (x, y, z) = x²z²į…

A: The vector field is V=x2z2i⇀+xyzj⇀+zcosy4k⇀. The position is (1,0,-1) The divergence is ∇·V is the…

Q: The thin rectangular bar AIB has mass m. Determine the intensity of the normal force at A and the…

A:

Q: The signboard truss is designed to support a horizontal wind load of 4 kN. A separate analysis shows…

A:

Q: Using hfg, Vfg, and Psat at 20°C from the ammonia tables, estimate the saturation pressure, in bar,…

A: Given: Initial temperature: →T1=20°C At this temperature from the ammonia table: →hfg=1185.9…

Q: 2. Honing is an operation performed as the operation. and 3. In sawing operation, the 4. For the…

A: Honing operation - In honing  a precision surface on a metal workpiece can be achieved by scrubbing…

Q: 4. Determine the DG. for the formation of Cu(NH3)42+ from copper (II) ion and ammonia all in aqueous…

A:

Q: A crane hook has a trapezoidal section at A-A as shown in Figure 2. Find the maximum stress at…

A: Given data: trapezoidal section of crane hookP=90KNbi=90 mmbo=25 mmh=116 mmRi=65 mmRo=65+116=181 mm

Q: applications of DE a body at a temperature of 200F is placed in room at a constant temperature of…

A:

Q: A cube is floating in oil (sg = 0.9). The sides of the cube are 100 mm and it is floating 75 mm deep…

A:

Q: Q1: Draw the following planes and direction in a tetragonal unit cell (410), (20-4). [321] and…

A:

Q: Q3// A 3-MW steam power plant have a water tubes boiler of the following specification: Steam…

A:

Q: Questions land 2 In the figure shown, F= 400 N, Determine the following: Q1) The magnitude and…

A: Given:The force acting on the structure, F=400 N

Q: Two parallel plates 0.5 m by 1.0 m are spaced 150 mm apart. One plate is maintained at 1,000 C and…

A: Given: Temperature of plate1 : →T1=1000°C=1273.15 K Temperature of plate2 : →T2=500°C=773.15 K…

Q: Air is discharged from a large tank through a convergent nozzle of 25 mm diameter. The air in the…

A: To find: The mass flow rate for the respective barometric reading. Given: Diameters, d = 25 mm.…

Q: The input speed of the worm shaft is 1200 rpm The worm wheel is made of phosphorbronze (sand cast),…

A: The convective heat transfer coefficient is h=25 W/m2°C. The effective area is A=0.25 m2. The…

Q: Oxygen at the rate of 3 lb/min undergoes a reversible isobaric process during which its entropy…

A:

Q: A container weighs 3.22 lb force when empty. Filled with water at 60°F the mass of the container and…

A:

Q: A two-stage centrifugal compressor (Figure 12.17) has the following data: First Stage Second Stage…

A:

Q: What is the total force on the object in the x-direction? a) 810 lb b) 926 lb Oc) 980 lb d) 1020 lb…

A: Given :  F1 = 800 lb F2 = 500 lb To find :  total force on the object in the x-direction

Q: A boat is aimed at the opposite shore of a 418.51 m wide river and rowed at a speed of 7.89 m/s…

A: To find: The speed of the boat relative to an observer. Given: The speed of the boat relative to the…

Q: Two identical uniform bars are welded together at a right angle and are pivoted about a horizontal…

A:

Q: If P₁= 330 lb, P2 = 230 lb, P3 = 330 lb, and dc=8 ft, determine the reaction at A and E. (Round the…

A:

Q: 34. During an isentropic process of 1.36 kg/s of air, the temperature increases from 4.44°C to…

A:

Q: From solution of equation for Unsteady state conduction of heat: y 2√at T = T₁ at y> 0 and t = 0 T =…

A:

Q: The disk shown in the figure rolls without slipping on the slope with an inclination angle of alpha…

A: Given Data The mass of the disc is: md=43 kg The radius of the disc is: r=1.4 m The rolling…

Q: 62 What is the network done by the gas as it goes from point A to B on the Pressure vs Volume…

A: Given data:  from P-V diagram P=100 pa V1=1 m3V2=3 m3

Q: 32.м т пу є 0.5 cm 12- 5 ст эт 0.5cm X

A:

Q: On the attached actual industry pictures, identify and pinpoint the possible hazards and risks.…

A: Given: In the picture a man is observing a motor system in which the conveyer belt is damaged…

Q: Given: V = 60 fps, u = 25 fps, ß = 120°. Determine V, in fps. Select one: O a. 31.3 O b. 29.3 O c.…

A: Given data: absolute velocityV=60 fpsvelocity of the bladeu=25 fpsangleβ=120°   Find out: The…

Q: The members CJ and CF of the loaded truss cross but are not connected to members BI and DG. Compute…

A:

Q: Using pressure-depth data (table below) obtained from a RFT test conducted on a well in a field,…

A: The data given is, Formation pressure in psia Depth (in inch) 5320 9793x12 5326…

Q: 4- Calculate the linear density of atoms (atoms/cm) in the [100], [110] and [111] directions in FCC…

A: According to the company's guidelines when multiple questions are asked only first question has to…

Q: A conduit connects two receptacle of different size. A valve is used at e end which can be opened or…

A:

Q: 4: For the following mechanism, (a) Find all instant centers (b) Find the mechanical advantage (MA)…

A:

Q: Classify the composites based on the matrix phase. Compare them based on their properties and…

A: Given question : Classify the composites based on the matrix phase. Compare them based on their…

Q: 23. Consider that 1 lb of air has a decrease of internal energy of 20.58 Btu while its Fahrenheit…

A: Given:mass of the air, m=1 lbdecrease of internal energy, ∆u=-20.58 BTUfinal temperature, T2=T13

Q: The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the…

A:

Q: A centrifugal pump running at 1859 rpm has impeller dimensions of b₁ = 53, b₂ = 21, r₂ = 285, r₁ =…

A: Given Data The width of the uniform blade 1 is: b1=53 mm=0.053 m The width of the uniform blade 2…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.