The amplifier circuit below has a single ac input and two ac outputs. Assuming transistor parameters of B - 100 and Vg = 0.6 V: a) Determine the Q point. b) Is the transistor in the active region? Explain thoroughly. e) Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. d) Draw a complete small signal circuit model, then find the voltage gain for both outputs. e) Based on the analysis results, what is the function of this circuit? Suggest a proper application. 2) Assuming that cach output is feeding a 50-k£2 resistor, determine the total voltage gain and current gain for both outputs. Also, calculate the amplifier input resistance and the amplifier output resistances." 10 V 10 V Rc= 3.3 kl 100 kf. 50 kN R = 3 kſl

The amplifier circuit below has a single ac input and two ac outputs. Assuming transistor parameters of B - 100 and Vg = 0.6 V: a) Determine the Q point. b) Is the transistor in the active region? Explain thoroughly. e) Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. d) Draw a complete small signal circuit model, then find the voltage gain for both outputs. e) Based on the analysis results, what is the function of this circuit? Suggest a proper application. 2) Assuming that cach output is feeding a 50-k£2 resistor, determine the total voltage gain and current gain for both outputs. Also, calculate the amplifier input resistance and the amplifier output resistances." 10 V 10 V Rc= 3.3 kl 100 kf. 50 kN R = 3 kſl

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure below shows a circuit for a pulse width modulator (PWM) amplifier. I. Describe how the circuit achieves low power dissipation 2. Describe with the aid of drawings the signal waveform shapes at points, A, B and C
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier.
C-A transistor supplies 2W to 4k2 load. The zero signal collector current is 35mA and the D.C. collector current with signal is 39mA. Determine the second order harmonic distortion.
1 a) Write down the equation that relates the collector current of the bipolar transistor to the base-emitter voltage. Hence prove the relationship 9mbe Bowhere the ac parameters are transconductance, base-emitter resistance and ac current gain respectively. c) Draw a schematic diagram of a simple current mirror circuit. Show how it can be extended to form a current repeater. How can the current repeater be improved to allow different bias currents to be realised?
1- Consider one Design or applications of MOSFET (can be as a small signal amplifier and digital switches) and explain its operation ?
This is about Bipolar Junction Transistors: Discuss collector characteristic curves and identify and explain the different regions.
Q. What is the purpose of using DC supply in amplifiers & oscillators circuits?
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'
In a full-bridge dc-dc converter using PWM bipolar voltage switching, analytically obtain the value of (V/V) which results in the maximum (peak-peak) ripple in the output current i,. Calculate this ripple in terms of Va, La, and f
This problem is AC analysis problem. DC analysis is not needed to answer the question. A) Convert this bias circuit into a bypassed common emitter amplifier that has an output across a load resistor (RL). To do this you should draw three capacitors on the figure below, an input voltage source, and any resistors you think that should be added. B) In the space below the figure, Draw the hybrid t model for this amplifier circuit including all voltages and resistors. Label Vi, Vbe, and vo on the model. Assume the capacitors you add act as short circuits at AC. Be sure to include resistors R1, R2, R3, R4, and RL in the hybrid pi model. > When you "verify" a mode of operation you will need to calculate all three voltages (Vc, Ve, VE for BJTS and VG, Vs, Vo for MOSFETS) and show the correct two conditions are satisfied. > Assume Capacitors acts like open circuits at DC and short circuits for AC. 12V Assume the following: o Beta = 100 O VBE = 0.7 o V: (Thermal) = 26 mV o Vr (Threshold) = 2V O…
draw the following systems: 1- AM generation -Square law product. 2- PM generation- frequency modulator.