The 5.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0, and has a stiffness of k-60 N/m. (Figure 1) Figure A-40Nm -05m- OC 50N-m 1 of 1 > Part A Determine the smallest angle for equilibrium Express your answer in degrees to three significant figures. for Part A Submit Provide Feedback for Part A for Part A undo for Part A redo for Part A reset for Part A keyboard st Request Answer for Part A help for Part A Next >

The 5.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0, and has a stiffness of k-60 N/m. (Figure 1) Figure A-40Nm -05m- OC 50N-m 1 of 1 > Part A Determine the smallest angle for equilibrium Express your answer in degrees to three significant figures. for Part A Submit Provide Feedback for Part A for Part A undo for Part A redo for Part A reset for Part A keyboard st Request Answer for Part A help for Part A Next >

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABCD of negligible weight is initially horizontal, and thesteel rods attached at A and C are stress-free. The 20-kip load is thenapplied and the temperature of the steel rods is changed by ΔT. Find ΔTfor which the stresses in the two steel rods will be equal. Use α=6.5x10-6/oF and E=29x106
Analyze the given structure: 12KN E 12KN 12KN 3m A 2m 2m 2m D Solve: 1. Member forces for EF GC BC
a uniform bar 1 is connected to a tapered rod 2. both are subjected to axial loads as shown. if P=7 kN, determine the axial deformation of tapered rod 2 (in mm). indicate negative sign if compression
Question #4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. O 2. T a 0.5m 0.5m 30 kN 2 m 100mm 50mm I 10mm 10mm 180mm Section a-a 10mm
(b) (5 pt) Draw and properly label a free-body diagram of ring A of the structure shown. Include only relevant information; do not include any information that is not relevant to the free-body diagram. Note: Assume the ring at A is massless. 3 m 3 m wwww kac = 20 N/m 4 m KAB = 30 N/m www. KAD = 40 N/m B
3: Analysis the structure shown in figure, El is constant W=20 KN/m P-40 KN B4 4m
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-110 GPa 3P E=200 GPa 7m 3M 80mm 30 mm 30 mm 80 mm 30 mm 30 mm
The line of action of the 2800-lb force runs through the points A and B as shown in the figure. Determine the x and y scalar components of F. у, m в (6, 5) F = 2800 lb - x, m A (-9, -3) Answers: Fx = Ib the tolerance is +/-2% Fy Ib
A uniformly tapered aluminum-alloy tube AB of circular cross section and length L is shown in the figure. The outside diameters at the ends are da and dB = 2d4. A hollow section of length and constant thickness t = A is cast into the tube and extends from B halfway toward A. t constant de- 21 B dg (a) dg (b) (a) Find the angle of twist of the tube when it is subjected to torques T acting at the ends. Use numerical values as follows: da = 2.8 in., L = 43 in., G = 3.5 × 10° psi, and T = 38,000 in. – lb. Round your answer to two decimal places. ФА (b) Repeat (a) if the hollow section has constant diameter da (see figure part b). Round your answer to two decimal places.
Q2 B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z=0 Y =0 (i) Determine the stress created at points A, B, and C. Note that moments of inertia for the circular area can be determined by I= (ar' )/ 4. y A M= 4ΥΟ Nm 45° Radius = 0.5(2Z) mm Figure Q2(b) I= 7 (0.5× DD Q2 b (i ) x10-“m* 4 4 - Mc, MN /m² @ MPa (Compression) I MC MN / m² @ MPa (Tension) I - Mc, -400x 0.5(20) sin 45 = x10“ m* |MPa (Compression) I
Q.4.b. A compound bar is made up by connecting a steel member and a copper member rigidly fixed at their ends as shown in figure below. The cross sectional area of the copper member is A while that of the steel member is 2A for half the length and A for the other half of the length. The coefficient of expansion for steel and copper are as-11.7*10ºC and a=17*10-/C respectively while the modulus of elasticity are E,=210Mpa and E=105MPA respectively. Estimate the stress induced in the members due to rise of 500 in temperature. 2A Steel Copper
At a temperature of 53°F, a 0.1 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a= 12.7 x 10-6/°F] and bar (2) is stainless steel [a= 10.4 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 40 in., L₂ = 57 in. (1) B A L₁ Answer: Final temperature = i bo L2 °F.