Take a look at the section below, consider is 30 inches long and has 0.1 inches of wall thickness.5 in-10 in-10 in-8000 lb10 in1) Calculate the shear flow in all the sections2) Determine the location of the shear center3) Calculate the bending stresses in each section4) Calculate the torsional stress in each section

The objective of the question is to calculate the shear flow, locate the shear center, calculate the…

Answered: Take a look at the section below,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. If the beam shown is uncracked, calculate the stress in concrete at the top and bottom extreme fibers under a positive bending moment of 80k.ft. 3 in. ● X= 4.75 w=8.5 u=6.75 v=8.5 S=11.75 in. 3 #10 Win. 18 in. Figure 1 in. Show Transcribed Text +++ E 27 in.
Wall shear stress calculate..
11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are circular fillets of in. radius on each side. If the bar is subjected to an axial tensile load of 12,000 lb, calculate (a) the average tensile stress in the wide portion of the bar some distance from the change in section. (b) the average tensile stress in the narrow part of the bar. (c) the maximum tensile stress adjacent to the circular wild fillet. 11 10 A long flat steel bar 5 in wide and in thick has a circu 162111 3 H ar 11.28 A P (a (E
Question 2: What force is required to punch a 20-mm-diameter hole in a plate that is 25 mm thick? The shear strength is 350 MN/m? Puncher - 20 mm sE 25 mm thick h Punched out 25 mm 20
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
Determine Stress in each section .
Question 3 Shear stress is directly proportional to the width of a section. O True O False
What would be the temperature at which the bar will have a compressive stress of 30 MPa given that at -20° celcius, there is a gap of 2.2 mm? E = 80,000 MPa. L=3m X-sechion: 350n A= 2. 2mm d = 18 x16-"/2 %3D O 40.7 "C O 43.5 "C O 41.6 "C O 45.8 "C
III. Locate the centroid of the composite area below. Y 50 80 mm, mm R=50mm 250mm R=65mm -- X 50 50 mm mm
What force is necessary to punch a 1 in hole in a 1/4 in steel plate if the ultimate shearing stress is 60,000 psi and the ultimate compressive stress is 100,000 psi? note: answer must be in kips
1. The prestressed beam is pre tensioned by a bonded prestress tendon having an area Aps = 650 mm2. fpu = 1728 MPa fpe = 988 MPa %3D fpy = 1486 MPa fc' = 27.6 MPa 300 mm |120 400 mm 600 mm 120 100 a. Find the value of the stress in prestressing reinforcement at nominal length. b. What is the design moment strength of the beam c. Is the beam over or under reinforced.
a hole is to be punched out of a plate having a shearing strength of 40 ksi. The compressive stress in the punch is limited to 50 ksi. (a) Compute the maximum thickness of plate from which a hole 2.5 in. in diameter can be punched. (b) If the plate is 0.25 in. thick, determine the diameter of the smallest hole that can be punched.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS