Table 2 ( R(Q) im(A) 0.031 100 200 0.009 330 0.005 100 0.018 2. Using Kirchhoff's Rules, construct enough mathematically independent equations to solve for the current of each resistor. Then calculate the % error between your measured and theoretical values for the current of each resistor. You MUST use Kirchhoff's Rules and show work R1 R2 it(A) R3 R4 ΔV1=5V % Error

Table 2 ( R(Q) im(A) 0.031 100 200 0.009 330 0.005 100 0.018 2. Using Kirchhoff's Rules, construct enough mathematically independent equations to solve for the current of each resistor. Then calculate the % error between your measured and theoretical values for the current of each resistor. You MUST use Kirchhoff's Rules and show work R1 R2 it(A) R3 R4 ΔV1=5V % Error

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An electric device draws 6.10 AA at 240 VV. If the voltage drops by 25 %, what will be current, assuming nothing else changes? Express your answer to two significant figures and include the appropriate units. I final= If the resistance of the device were reduced by 25 %, what current would be drawn at 240 VV? Express your answer to two significant figures and include the appropriate units. I final=
A TV works properly under the voltage of 4V= 110 V with power P = 1560 W. Express the current I through the power P and the voltage AV. I = Calculate the working current of the TV in A. I = Express the resistance R through the voltage AV and the current I. R = |Calculate the numerical value of R in 2. R =
What is the equivalent resistor between the terminals a and b if you replace R1 by 38 Ohm and R2 by 34 Ohm ? This combination of resistors goes to infinity by repeating itself. Write your answer in units of Ohm. No decimal points is necessary. Maximum od 4% of error is accepted in your answer.
The compressor on an air conditioner draws89.6 A when it starts up. The start-up time isabout 0.282 s.How much charge passes a cross-sectionalarea of the circuit in this time?Answer in units of C.
1.9. A block of conductor has the dimensions Lo x 2Lo x 4Lo. As shown in the figure below, the same battery is connected across the conductor in three different configurations. Which configuration draws the smallest current from the battery? All configurations draw equal current. 21 Lo 4Lo 4LO (a) (b) (c) (d)
Solve the following: 1. How many nanocoulomb are there in 3.65 billion electrons ? 2. A 25 ampere electric current flows in a conductor in 75 millisecond. Find: a. current equivalent in mA? b. How many charges are transferred ? c. How much work is required to transfer if 3V is applied. 3. A charge of 3.5 µC present in an electric field produces a force of 0.008 Newton. What is the intensity of the electric field ? 4. A charge of 0.6 µC is placed in an electrostatic field whose intensity is 3 x 105 N/C. How strong is the force acting on the charge ? 5. Two objects are both negatively charge with 0.04 coulomb each and 140 cm apart. What kind of force exist Between charges? How much? 6. Find the force that exist between two charges of 8.53 μC and 4.5 µC that 0.25 meters in air?
2. A = area -L = length - Calculate the resisitance per unit length of a Nichrome wire of a. |=-W Radius 0.321mm. (Resistivity Nichrome= 150x10* Q.m) p = resistivity of R b. If a potential differnces of 10 V is maintained across a 1 m length of the Nichrome wire, what is the current in the wire? 4.00 kO
HW Q1.Nichrome wire has resistivity p=1.5*106 (Q.m) calculate the following a. The resistance per unit length if the radius of wire is 0.321 mm? R-4.6 Ωm b. If the potential difference of 10 V is maintained across a 10m length of Nichrom wire ,what is the current ? I=2.2A Q2Silver wire with cross section area 0.923mm2 , the resistivity = 10.49g/cm and the molar mass M=107.9g/mol, if the current pass though the wire is 0.123mA, calculate : 1.The electron density 2.The current density 3.Drift speed (va=1.42*10-3 m/s) %3D (n=5.855*1028 e/m') (j-133.26A/m2 ) Q3.a.Calculate the current density for Aluminum wire has radius 1mm and current 1mA? 318.31A/m? b. Calculate the drift speed for electrons in the wire ? 3.29*108 m/s if the pAL-2.7*10 kg/m3 and if you know that one mole in the Aluminum has mass equal to 26.98g and there is one conduction for each Aluminum atome?
that pass per second through a section of wire carrying a A. E. Solve for the resistance of a conductor given a resistivity of 15.3 £-m, length of 6m, and cross sectional area of 2.85 x 10² m². F. A copper rod is 3 m long and 4 mm in diameter. Compute its resistance if the resistivity of the material is 1.76 x 108 -m. G. A piece of number 10 aluminum wire has a diameter of 2.59 mm. How many meters of number 10 aluminum wire is needed to give a resistance of 1 ? Aluminum has p of 2.8 x 10³ Q-m. H. Compute the Resistance of a 190 m wire made of silver having a cross-sectional area of 0.55 mm². Silver has a resistivity of 1.6 x 10³ N-m.
In the circuit shown, Determine the following: A. Magnitude and direction of the current (Ans. I = 0.3889 A, CCW) B. The potential differences Vad, Ver and Vre
Current=1A V_ab=-12V V_bc=21V 4d. What is the total rate at which electrical energy is dissipatate in R1, R2, and R3 resistors. 4e. What is the power outpur of the 26V battery? 4f. At what rate is the electrical energt being converted to other forms in the 10V battery? 4g. Show that power output of the 26V battery equals the overall rate of dissipation of electrical energy in the rest of the circuit?
Consider the resistor network shown in the figure, with R₁ = 250 [N], R₂ = 1.0 [kN], R3 = 1.2 [kn], R4 = 1.0 [kn], and R5 = 1.5 [k]. The source voltage & is 24 [V], and has no internal resistance. What is the current passing through R₁? W R₁ www www.m R₂ O A. 34 [mA] B. 54 [mA] OC. 96 [mA] OD. 104 [mA] www R3 www-www R4 R5