RTD is a common temperature detector in oil industry. The figure bellow shows the behavior of three commonly used metal for RTD construction. Evaluate the stability of these metals at different temperature range. Which is the best option for temperature measurement higher than 200 C? Justify your answer.

RTD is a common temperature detector in oil industry. The figure bellow shows the behavior of three commonly used metal for RTD construction. Evaluate the stability of these metals at different temperature range. Which is the best option for temperature measurement higher than 200 C? Justify your answer.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter1: Atomic Structure

Section: Chapter Questions

Problem 6RQ: How many valence electrons are generally contained in materials used for insulators?

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
How many valence electrons are generally contained in materials used for insulators?
A. Explain the difference between charging current andfaradaic current. B. What is the purpose of waiting 1s after a voltage pulse before measuring current in sampled current voltammetry? C. Why is square wave voltammetry more sensitive than sampled current voltammetry?
At 305 °K temperature, the voltage equivalent of temperature of diode is ______________________V. Assume the Boltzmann's constant is 8.62*10-5 eV / K Answer:
In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2..
Two silicon diodes are connected in parallel and in series with resistor 0.33kohms and a battery of 10V. the voltage across the resistor 0.33k ohms is ___. The current flowing through resistor 0.33K ohms is approximately equal to___. The current of one diode is___.
1. Answer the following with "TRUE" or "FALSE" then explain why. ________a.) Charges choose the path of least resistance. Given a resistor in parallel with a diode, no current willflow through the resistor when the applied voltage exceeds the diode’s forward voltage.________b.) Since diodes are unidirectional components, it will always block AC signals e.g. pulse train,sawtooth, triangular signals.________c.) Silicon diodes typically have a forward voltage of 0.7V.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
The datasheet shown below for a group of commercial Zener diodes, according to the datasheet the typical voltage and leakage current of the Zener diode with model number 1N4732A are: * Tolerance- S% FAIRCHILD SEMICONDUCTOR Datasheet 1N4728A - 1N4758A Zener Diodes D0041 Glass case Electrical Characteristics 1,-25°C untess otherwise noted Vz (V) @ Iz (Note 1) Max. Zener Impedance Leakage Current Test Current Device Zz@lz ZzK @ IZK (mA) IR (HA) VR (V) Min. Тур. Мах. Iz (mA) (오) Izk (2) 3.315 3.42 1N4728A 3.3 3.465 76 10 400 1 100 1 1N4729A 3.6 3,78 69 10 400 100 1N4730A 3.705 4.085 3.9 4.095 64 9 400 50 1N4731A 4.3 4.515 58 400 10 1N4732A 4.465 4.7 4.935 53 500 1 10 1 1N4733A 4.845 5.1 5.355 49 550 10 1 1N4734A 5.32 5.6 5.88 45 600 10 1N4735A 5.89 6.2 6.51 41 2 700 1 10 3 1N4736A 6,46 6.8 7.14 37 3.5 700 1 10 1N4737A 7.125 7.5 7.875 34 4 700 0.5 10 b. 1V and 10uA O c. 4.7V and 10uA a. 4.465V and 10UA O d. 4.7V and 53mA
Turn off the function generator and build the following circuit. Make sure that the zener diode cathode is on the positive voltage side as shown below before you turn on the function generator again. How can you determine when the zener diode is conducting?
The three-phase circuit shown in figure 1 is 220 Vrms per phase and 50Hz. Diodes are real. The circuit produces an output shown in Figure 2. Indicate the conduction angle of diode D5. What times does this conduction correspond to? Use the first cycle only (0-360°). to-0 sec.
1)Define Drift and Diffusion current in Semiconductor. 2. Why n - type impurities are called as Donor impurities? 3. Give the other names of depletion region? (At least Two) 4. General Purpose Diodes are mostly preferred in chopper circuits. Is it True? Justify.