QUESTION 1 Problem 1: A continuous-time signal xc (t) = 2sin(25πt) + sin(15πt) + 4 sin (20лt) + 2 sin (30nt) + 3 sin(35nt) is sampled at a rate of 25 samples/s and then passed through a perfect D/A converter to produce the analog signal ye(t). (a) Identify which terms in xc (t) are aliased. (b) Find y(t).

QUESTION 1 Problem 1: A continuous-time signal xc (t) = 2sin(25πt) + sin(15πt) + 4 sin (20лt) + 2 sin (30nt) + 3 sin(35nt) is sampled at a rate of 25 samples/s and then passed through a perfect D/A converter to produce the analog signal ye(t). (a) Identify which terms in xc (t) are aliased. (b) Find y(t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A nonperiodic composite signal has a bandwidth of 170 kHz, with a middle frequency of 120 kHz and a peak amplitude of 20 V. The two extreme frequencies have an amplitude of 10 V. 1. The lowest frequency is KHz. 2. The highest frequency is KHz. Draw the frequency domain of the signal. (You don't need to submit the curve to the Canvas.)
b) Create a new folder name Lablb in your D:\Student_Matric_Number. Find the output X and show the simulation waveform. A B
Design an RC circuit where the output always leads the input by a large amount:• Describe the relative values of R and C (using words like “large”, “medium”, or “small”,rather than numbers) and if the output amplitude is large or small.• Do you measure the output across the capacitor or resistor?• Sketch the input (source) and output voltage sine waves.
Ex: Design a noninverting summer circuit to achieve a 3 summing function for two analog signals 3 filt) = 5 Sin 2πT 10³t and f(t) = Ult). Draw the output waveform.
Problem #2 - A digital signal is to be represented by a positive voltage A for a "1" and negative voltage -A for a "0". It will be detected by taking a single sample and seeing whether the result is positive or negative. However, there is also added noise in the system with an rms value of 0.5V. What value of A is required to reduce the probability of error to 10-7
e) Compute the integral -3" cos(2u)8(5u - 1)du
Q6. Figure Q6 shows a modulated waveform v(t) in microvolts as a function of time t in nanoseconds. 25 50 75 100 125 150 175 200 225 250 50 40 40 30 30 20 20 10 10 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 250 25 50 75 100 125 150 175 200 225 time/ns Figure Q6: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) The modulating wave in this example is substituted with a square wave of 50% duty cycle and of fundamental frequency 1.0 MHz. Sketch the absolute value of the spec- trum of the modulated waveform indicating the frequencies and relative magnitudes of the sideband components. (g) Demodulation of this type of signal is usually accomplished…
A carrier signal with frequency of 1 MHz and peak-to-peak amplitude of 10√2v is added to a single tone message with frequency of 1 kHz and peak-to-peak amplitude of 4√2v. Then passed through a diode having the following c/cs: i(t) = e(t) + 0.5e²(t), find: 1- Modulation depth of DSB signal. 2- Frequency of each component in the diode current.
If the TIME/DIV is set to 0.2 ms, what is the time constant of the circuit? X ms An oscillator with a natural frequency of 380 Hz is driven by a 580 Hz sinusoidal signal. At what frequency does it oscillate?
3- Analyze the system shown below to find the output waveform, Vout, assume the capacitor voltage value is -1.0 V at t-0 and RC-1 msec. -0.5 -1.0 V(1), V 1.0 0.5 R $ AAA f, msec
A particular circuit built with one resistor and one capacitor in series allows high frequency source voltage sine waves to be transmitted as the output essentially unchanged. Any low frequency source voltage sine waves are “killed”; the output is very small, essentially zero. Design this circuit: draw the circuit and explain whether you measure output over the resistor or capacitor, and why. You do not need to choose values of R and C.
it in B- Consider the analog signal x(t) What is the Nyquist rate for this signal? 3cos50 mt + 10sin100 nt + cos150 nt Choose one C