Question 1 A 300 m ring distributor has loads as shown in Figure Q1 where distances are in metres. The resistance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. 240 V 50 A 60 60 D A B 70 70 90 90 100 A 80 60 0 70 A Answer Figure Q1.

Question 1 A 300 m ring distributor has loads as shown in Figure Q1 where distances are in metres. The resistance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. 240 V 50 A 60 60 D A B 70 70 90 90 100 A 80 60 0 70 A Answer Figure Q1.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

An ac resistance is higher than a dc resistance. True False
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
Discuss the relationship between voltage break down and humidity, temperature and distance explain with curve
. Using the I – V curves how are ohmic materials different from non-ohmic materials
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
use kirchhoffs Junction rule and loop rule to solve for currents I1 , I2 and I3..