QI/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the rpm of the motor is 600. The diameter of the machine pulley C is 180 mm. The ratio of the tight- and slack- tensions on the belt is 3. Two bearings A and B support the shaft. The shaft made from carbon steel with SAE number 1040 cold rolled. Determine the shaft diameter if the torque applied is dynamically reversed and the bending moment is applied statically. The pulley and gear are mounted on shaft using keyways. Design these keys if the key material is the same of the shaft material. Fig. (1)

QI/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the rpm of the motor is 600. The diameter of the machine pulley C is 180 mm. The ratio of the tight- and slack- tensions on the belt is 3. Two bearings A and B support the shaft. The shaft made from carbon steel with SAE number 1040 cold rolled. Determine the shaft diameter if the torque applied is dynamically reversed and the bending moment is applied statically. The pulley and gear are mounted on shaft using keyways. Design these keys if the key material is the same of the shaft material. Fig. (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a plain carbon steel centrecrankshaft for a single acting four strokesingle cylinder engine for the following data:Bore = 400 mm; Stroke = 600 mm; Enginespeed = 200 rpm; Mean effective pressure =0.5 N/mm2; Maximum combustion pressure= 2.5 N/mm2; Weight of flywheel used as apulley = 50 kN; Total belt pull = 6.5 kN. Theratio of the connecting rod length to thecrank radius is 5. Assume the crank is at topdead centre. Assume any other datarequired for the design
Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as found from the turning moment diagram is to be 0.15 and the fluctuation of speed is energy as feed 1% of the mean speed. Find the weight of the flywheel required, if the radius of gyration is 1.5 m. T
In a thrust bearing, the external and the internal diameters of the contacting surfaces are. 19 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m?. The shaftrtates at 400 rpm. Taking the coeffic. : of fricieơn as 0.Q6 calculate the power lost fi overcoming the frP. Con. Also, find the number of collars required for the bearing. rrs
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
An engine of a motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiencyof the differential and transmission is 75% with an over-all speed reduction to. 1 determine he torque to bedelivered by the clutch N-m.
A 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20° stub teeth .the centre to centre distance between the shafts is 400mm.the motor pinion is made to forged steel having an allowable static stress 210MPa while the gear is made of cast steel having an allowable static stress as 140MPa.Assuming that the drive operates 8 to 10 hours per day under light shock conditions,find from the standpoint of strength (a) Module;(b)face width and (c)number of teeth an pitch circle diameter of each gear.check the gears thus designed from the consideration of wear .the surface endurance limit may be taken as 700MPa.
3. A 15 kW and 1200 rp.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa.[Ans. m 6 mm ; b = 60 mm; Tp= 24; T=96; D, = 144mm; De= 576 mm]
1. A four stroke internal combustion engine has the following specifications: Brake power = 7.5 kW; Speed 1000 r.p.m.; Indicated mean effective pressure = 0.35 N/mm2;Maximum gas pressure = 3.5 N/mm2; Mechanical efficiency = 80 %. Determine: 1. The dimesions of the cylinder, if the length of stroke is 1.4 times the bore of the cylin- der; 2. Wall thickness of the cylinder, if the hoop stress is 35 MPa; 3. Thickness of the cylinder head and the size of studs when the permissible stresses for the cylinder head and stud materials are 45 MPa and 65 MPa respectively.
1. A bearing for an axial flow compressor is used to support a radial load of 2500 N and thrust loads of 1500 N. The service required for the bearing is 5 years at the rate of 40 hours per week. The speed of the shaft is 1000 rpm. Select suitable ball bearing for the purpose Diameter of shaft is 50 mm.
Torque required for achieving the tighting force
The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O c. 0.92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is N, Take pressure angle as 14½0. at Pitch P. point Gear driven to 02 The radial force is